"
Team:Paris Saclay/PS-PCR/detailed description
From 2013.igem.org
| Line 10: | Line 10: | ||
This project aims at creating a thermal cycler for under 30€ with easily accessible parts. | This project aims at creating a thermal cycler for under 30€ with easily accessible parts. | ||
| - | === Comparison with other | + | === Comparison with other projects === |
Some open source PCR thermal cycler projects already exist, but the aim of the PSPCR project is to provide a better and more affordable system, thus filling a gap in the list of existing projects. | Some open source PCR thermal cycler projects already exist, but the aim of the PSPCR project is to provide a better and more affordable system, thus filling a gap in the list of existing projects. | ||
| Line 41: | Line 41: | ||
|- | |- | ||
|} | |} | ||
| - | |||
== Design overview == | == Design overview == | ||
TODO inclure schema | TODO inclure schema | ||
| - | |||
=== Solid state heating/cooling === | === Solid state heating/cooling === | ||
| Line 71: | Line 69: | ||
=== Temperature sensing === | === Temperature sensing === | ||
| + | |||
| + | Sample temperature feedback is done thanks to a thermistor attached to the sample holding block. A thermistor a resistor with a temperature-dependant value. By using a voltage divider, one can easily use it to obtain a measurable temperature-related voltage. | ||
| + | |||
| + | TODO schema | ||
=== Digital interface === | === Digital interface === | ||
| Line 76: | Line 78: | ||
The digital control system is built around the Atmega8 inexpensive micro-controller which generates the PWM signal for the Peltier device, outputs current direction commands to the H-Bridge subsystem, acquires values from the temperature feedback sensors and provides an USB port for communication with a computer. | The digital control system is built around the Atmega8 inexpensive micro-controller which generates the PWM signal for the Peltier device, outputs current direction commands to the H-Bridge subsystem, acquires values from the temperature feedback sensors and provides an USB port for communication with a computer. | ||
| - | The whole system is | + | The whole system is controlled through the USB port by a computer running specifically designed software. The computer reads temperature feedbacks and sets the Peltier heat transfer direction and power. The software running on the computer provides a user interface allowing the user to select the PCR cycles to run. |
== Construction == | == Construction == | ||
Revision as of 23:25, 16 September 2013
Contents |
PSPCR
The Paris-Saclay open source PCR thermal cycler project.
Introduction
PCR (Polymerase Chain Reaction) is a very useful procedure in the field of synthetic biology. However, this technique requires a device called a thermal cycler, which is designed to cycle the samples through different temperature steps. Commercial PCR thermal cyclers are traditionally very expensive, with prices starting at $2000, which makes them hard to afford for small labs and DIY projects.
This project aims at creating a thermal cycler for under 30€ with easily accessible parts.
Comparison with other projects
Some open source PCR thermal cycler projects already exist, but the aim of the PSPCR project is to provide a better and more affordable system, thus filling a gap in the list of existing projects.
| Project | Price | Discussion |
|---|---|---|
| [http://openpcr.org/ OpenPCR] | $649 | Heated lid, good performance, hard to manufacture. |
| [http://www.instructables.com/id/Arduino-PCR-thermal-cycler-for-under-85/ Arduino PCR] | $85 | No heated lid, room for only 2 tubes, fan-only cooling. |
| [http://lavaamp.wordpress.com/ Lava-Amp] | "pennies" | No data available, probably slow with no heated lid, 1 slot. |
| [http://www.instructables.com/id/Coffee-Cup-PCR-Thermocycler-costing-under-350/ Coffee Cup PCR] | $350 | 7 slots, no heated lid, fan-only cooling. |
| PSPCR | Under 30€ | Fast solid state heating/cooling, 16 slots, heated lid. |
Design overview
TODO inclure schema
Solid state heating/cooling
By using a [http://en.wikipedia.org/wiki/Peltier_effect#Peltier_effect peltier thermoelectric device], the system achieves fast heating and compressor-less cooling, enabling it to reach temperatures ranging from -3°C to 120°C in a relatively short time.
When powered, the Peltier block transfers heat from one of its sides to the other, thus cooling the former while heating the latter. The "heat pumping" direction can be flipped by reversing the direction of the current in the device.
One side of the Peltier is thermally attached to the sample holding aluminium block, while the other one is attached to a computer CPU fan-thermalized radiator. Since the fan keeps the radiator at near-room temperature, the Peltier device can pump heat from(to) it in order to heat(cool) the sample holding block.
Power control
In order to control the current inside the Peltier, and therefore the heat pumping power, the system uses PWM (Pulse Width Modulation). PWM is quite a simple technique : instead of continuously adjusting the current through the Peltier, it works by switching the peltier completely on and off using a high frequency (~1kHz) square signal. The ratio between the duration of the "on time" and the duration of the "off time" in a single signal period defines the mean power provided to the device : 1.0 meaning full power (Peltier always powered), 0.0 meaning zero power (device always off), 0.2 meaning 20% power (Peltier on 20% of the time, and off 80% of the time) for example. This method uses simple binary to control the Peltier power, allowing the usage of a digital micro-controller to drive the Peltier.
TODO image signal crénau
The direction of the current inside the Peltier is controlled using a power H-Bridge circuit. Our H-Bridge consists of two pairs of complementary power MOSFET transistors that can be selectively switched using digital signals in order to choose the direction of the current through the Peltier.
TODO : images 2 situations h-brige
Temperature sensing
Sample temperature feedback is done thanks to a thermistor attached to the sample holding block. A thermistor a resistor with a temperature-dependant value. By using a voltage divider, one can easily use it to obtain a measurable temperature-related voltage.
TODO schema
Digital interface
The digital control system is built around the Atmega8 inexpensive micro-controller which generates the PWM signal for the Peltier device, outputs current direction commands to the H-Bridge subsystem, acquires values from the temperature feedback sensors and provides an USB port for communication with a computer.
The whole system is controlled through the USB port by a computer running specifically designed software. The computer reads temperature feedbacks and sets the Peltier heat transfer direction and power. The software running on the computer provides a user interface allowing the user to select the PCR cycles to run.
Construction
Tolerant design
The PSPCR cycler uses a novel approach for DIY construction : part tolerance. Indeed, the system has the unique property of being tolerant to reasonable component variations. This lets users choose parts they may already have, or that they can get more easily.
