The Riding

The Riding

In this synthetic symbiosis, C. elegans acts as a transport for engineered bacteria (Pseudomonas putida) in order to take them to the hotspot of interest, because bacteria are are not able to move fast in through solid or semi-solid substrates but they are very interesting from a biotechnological point of view, that is the reason why we though in this innovative mean of transport: the regulated formation of a biofilm.

To achieve our goal, we constructed a BioBrick (see part: BBa_K1112001) consisting in the coding sequence of the hmsHFRS operon, an adhesion operon natural from Xenorhadbus nematophila which allows the formation of a biofilm on the nematode S. carpocapsae, under the control of a nitrogen sensitive promoter (pGlnA, characterized by the 2012 Valencia Biocampus iGEM team). (Fig.1)

Controlling the mechanism

Riding was a regulated process: with low nitrogen in the media, the promoter is activated and hms genes are expressed, triggering the formation of the biofilm over C. elegans; in contrast, with high nitrogen concentrations, such as the ones found in nutrient-rich hotspots, the promoter is repressed, so bacteria can “get off” the nematode (Fig. 2).

Biofilm formation in genetically-engineered bacteria

Our original idea was to introduce the Biobrick in Pseudomonas putida , a bacterial species with wide applications in biotechnology. To do that, we cloned the construction (Fig.1) in the pIZ1016 vector, which has a replication origin compatible with Pseudomonas. We successfully performed the cloning (Fig.3), but the efficiency of the transformation was too low, so haven’t been able to obtain P. putida transformants yet. This is probably a consequence of the length of the construction, 6,5 kb, which decreases transformation efficiency.

But far from being disheartened, we decided to express the construction with E. coli. We cloned the construction in the pUC57 vector, obtained transformant E. coli, and then grew them in medium with low nitrogen (0,6 g/L) in order to induce the formation of the biofilm.C. elegans was fed with these induced bacteria, and then several worms were isolated in order to check biofilm formation with scanning electron microscopy (SEM) imaging. As you can see in Fig.4, we actually did it! We observed a formation of an E. coli biofilm over the nematode!

The Calling

The Calling

Looking for an attractant

When we were considering setting up a transport of bacteria was thought to be necessary to have a 'destination', a place to go. That destiny would be a 'hot spot' on a heterogeneous substrate where Caenorhabditis elegans should lead right to that point the bacteria.
Leveraging the powerful smell of the nematode, it was decided to try a number of attractants from various lists from web www.wormbook.org that could work as 'hot spot' of our experiment. Thus, using the C. elegans chemotaxis, we could direct transport.

The attractants experiment

The test would be carried creating our own plates on which half would be NGM unmodified and the other half part would be including soluble compounds before solidifying or after solidification in the case of volatiles. The list of modifications can be found in Fig. 1.

To place C. elegans on the plate, different cuts were made on a fresh plate of NGM, the resulting small pieces were placed in the exact center of the 50% -50% plates to determine which side of the nematode preferred, one per Petri plate.

The results after counting 2 replicates per attractant can be seen in Fig. 2.

From Table 2 it could rule out many of the attractants that were thought viable.

Volatile attractants were not a good choice to evaporate quickly (which is also limited to the field experiments).

Another impediment arose. Once had already performed the experiments, it was decided that the promoter that will control the production of RNA interference in Escherichia coli would be controlled by nitrogen, amino acids had to be discard as attractants; it would modify controlled expression of E.coli.

That left the MgSO₄ and hypoosmotic media as potential attractants.

Attractant final choice

Because the hyposmotic medium could interfere with the proper growth of bacteria (food of our nematode), the final decision was to choose the MgSO₄ as attractant.

The question that arose at that time was: How we can multiply the amount of MgSO₄ to increase efficiency?

MgSO₄ efficiency

Once we had selected the most feasible attractant to the ‘transport’ for our experiments, we needed to know what could be the largest concentration of MgSO ₄ in order to optimize the attraction of the nematode.
To choose the concentration, were tested in a battery of increased concentrations regarding the initial medium (1 ml / L). Bearing in mind the results of the factor x2, we decided to test other factor concentrations: x3, x4, x5, x8 and x10; covering a range that does not exceed the concentration at which might affect the life of C. elegans or bacteria.
Moreover, approaching experiments with E. coli and Pseudomonas putida, these trials were testing the end media: half plate with NGM non-altered and half as PHA production medium for Pseudomonas and interference of E. coli.
Not knowing what fatty acid could activate transcription better, we tested two possibilities: oleic acid (named in the tables as PHAol) and octanoic acid (PHAoc). The concentration for each fatty acid was tested in E. coli choosing as better:

• 1.28 µl/ml of Octanoic acid.
• 2.58 µl/ml of Oleic acid.

You can see our results in figures 3, 4, 5 and 6. The two first counts were made after 3 hours and the next ones after 6 hours. We suppose at that time the worms can select their “favorite” half part gone across and their movement would be always in the same area. We prepare as control plates with the same composition but without MgSO₄ in PHA media.

Final concentration choice

Once the test already performed and that the results seen by the factor of PHA and MgSO₄ selected fatty acid give very scattered (there is probably repellent effect at high concentrations in the medium with oleic but reversed in octanoic) we make a selection of MgSO₄ concentration for each medium.

• If it is used oleic acid à Better results with 4ml/L MgSO₄.
• If octanoic acid used à Best results to 10 ml/L of MgSO₄.

Octanoic was discarded as a transcriptional activator of the iRNA of clumping after other result of E. coli, so finally we selected PHA medium with oleic acid.
The biggest problem in trying to have an effective attractant was how effective could be in presence of E. coli. It was therefore necessary to test the tradeoff between the value of 4ml / L MgSO₄ and pair it with different concentrations of bacteria, high enough to feed the nematode but low enough to permit the attractive effect of MgSO₄.
To find this point of commitment we prepare experiments in which the concentration of 4ml/L of MgSO₄ is faced against different ODs from serial dilutions of a preculture of E. coli DH5a.
Table 7 shows the results. The count took place at 3h after the passing of fresh nematodes.

Best E. coli OD choice

An OD of 1 (minimum concentration of cells / volume) gives an attractive effect even better than expected (subsequent experiments try to see if there is synergy between E. coli and attractive factors MgSO4).
To improve the approximation was decided to repeat the experiment with MgSO₄ concentration and the chosen bacteria OD showing that the system works well. The results can be seen in figure 8.

The Clumping

The Clumping

The base of this part is our engineered E.coli with a biobrick that is capable of changing the worm’s behavior.

Our C. elegans strain (N2 strain) has two feeding behaviors: Social and solitary feeding. Social feeding is known as clumping as you can see in this video:

Clumping is known to be induced under some conditions like temperature or starving, something that we had had considered during the entire project. However, it is also known how clumping is controlled from a genetic perspective and the main genes have already been described. We thought we could use this genetic approximation to control clumping under specific and controlled conditions. (view “Natural variation in a neuropeptide Y receptor homolog modifies social behavior and food response in C. elegans.” Bono M, Bargmann CI).

How do we induce clumping?

Our initial thought was to interfere the principal gene involved in this route: NPR-1. It is known that mutations in NPR1 convert a solitary strain into a social strain. Another option we finally chose was FLP-21, a gene that positively regulates NPR-1. We selected this one instead because it is not involved in so many vital processes. FLP-21 encodes a single FMRF amide-related neuropeptide that serves as a ligand forNpr-1, a G protein-coupled receptor that regulates social versus solitary feeding behavior in several Caenorhabditis species (see fig. 1).

So, this would be the final process: engineered E.coli that expresses FLP-21, whom RNA will interfere with the one codified by the worm because of the ingestion of bacteria. The formation of a complex of dsRNA will induce the elimination of Flp-21 transcripts by the RNA silencing pathway, which consequence is the induction of clumping (see figure 2). We also had to take into account that the induction of clumping by this mechanism is almost immediate, in comparison with natural clumping which takes longer depending on the external factors.

Why do we induce clumping for?

The main objective of the synthetic symbiosis that we designed was to detect hotspots of interest in irregular substrates and the induction of clumping was a good tool for it. With this natural mechanism, which we were going to control, worms kept in the desired places, then bacteria transported by C. elegans (Pseudomonas putida) were concentrated where their action was needed, in order to generate value-added products such as bioplastic PHA and the increase of worms in a specific location improved the image-based detection mechanism (go to Devices section)

Controlling the mechanism

The social feeding behavior needed to be controlled; it might be induced by conditions of interest as a tool for detecting hotspots in irregular substrates. We decided that fatty acids were going to be the inductors of the promoter (fadBp) that regulated the expression in the FLP-21 antisense sequence, in order to induce RNA interference (Fig.3). In the fatty acid rich media where this mechanism was activated, bacteria got off the worm, so this construction allows the induction of clumping in the spots where a biotechnological process will be carried out.

Choosing the right fatty acid

The E. coli’s biobrick promoter is induced by fatty acids, but those also induce the promoter of Pseudomonas putida in order to produce PHA. Some investigations showed that the induction of fadBp promoter by oleic acid is the most efficient (view “Regulation of fatty acid degradation in Escherichia coli: analysis by operon fusion” Clark D. et al) is higher when the fatty acid used is oleic acid but this is a long chained compound and that could affect the production of bioplastic (PHA). We decided to test the growth of E. coli and the production of bioplastic by P. putida using PHA media with oleic acid and octanoic acid in order to get the best results in both activities.

Both species of microorganisms where grown in PHA production media with different concentrations of oleic and octanoic acids, maintaining a global concentration of fatty acids of 8mM, because it was the one where we found the highest growth of both E. coli and P. putida. Table 2 (below) summarizes the assays done.

The results of this assay showed that E. coli growth was better on PHA production media + 8mM oleic acid and the P. putida production of bioplastic was acceptable in this conditions. However, the highest production of bioplastic was on PHA production media+ 8mM octanoic acid one. So then, we made a Colonization assay and finally we determined that we were going to continue working using the PHA production media + 8mM oleic acid. Also, the ODs for plating both organisms were stablished as a consequence of this experiment. The “Choosing the right fatty acid” and the “Colonization” assays are explained at Building the bioplastic section.

Observing clumping induced by fatty acid rich media

We could see how clumping was done induced by the presence of 8mM of oleic acid (2.58 µl/ml ) which regulated the FadBp promoter of E. coli and as a consequence the expression the complementary sequence to the worms’ FLP-21 transcript, producing interference by RNA. In the plates there was a high concentration of E. coli from the serial centrifugations preculture 4ml XL1-Blue, 2 min at maximum rpm (2 times). The following images show the change of behavior of C. elegans, which at first were eating alone and then they were doing it in groups as it was planned (Fig. 4-6).

The Building

The Building

We decided to include in the mechanism design a regulated production of a value-added product in the hotspots of interest were C. elegans would be attracted to. We got proffit of the natural capacity of Pseudomonas putida of producing bioplastic PHA (polyhydroxyalkanoates) by bacterial fermentation of sugar or lipids (fatty acids in this case), because we found that the directed production of this versatile material was interesting due to its easy detection (complexes of PHA with red Nile are fluorescent), its bright future in the field of biomaterials and because we were using this natural ability of bacteria as a tool.

The mechanism

A cluster of genes is responsible of the production of PHA, the phaC operon of P. putida which consists of 4 ORFs that are transcribed in the same direction: phaC1 and phaC2 genes, codify for two PHA sintases; phaZ gene, codifies for a despolimerase; and phaD gene, that codifies for a protein of the TetR family. In the opposite direction two genes that codify for fasinas (phaF and phaI) and structural proteins are found (Fig.1).

The role of the operon in our project

Our 2013 project is a proof of concept of the benefits that an artificial synthetic symbiosis between bacteria and nematodes can offer. The roles Pseudomonas play are two: firstly, they have been engineered to “ride” on C. elegans by the formation of a biofilm, but not stuffed with that, under the promoter glnA we stimulated the production of PHA, a value-added product that can be widely applied, for example:

• For short disposable packaging items (personal hygiene products, surgical clothes).
• In upholstery.
• In the photographic and printing industry
• For textile industry since PHA can be processed into fibers.
• For biofuel production from PHA obtained from sewage sludge. This would combine two major advantages: the wastewater treatment and the generation of energy.

Choosing the right media

On the plates we were going to have both P. putida and E. coli and their promoters’ response towards fatty acids was different, so we had to make a media where E. coli could induce clumping and P. putida the production of bioplastic. In E. coli, the briobrick promoter for the expression of FLP-21 iRNA engineered in order to induce the social feeding behavior of C. elegans (Clumping) is induced by fatty acids, but not all the fatty acids are able to induce the same level expression (Fig. 2); oleic acid produces the highest activation of the promoter.

Whereas the standard medium for the production of PHA by Pseudomonas putida (composition reflected in Fig.3) employs octanoic acid (a short-chain fatty acid) as inducer. This fact made necessary to check if the modification of the fatty acid used, octanoic by oleic, would modify the bioplastic (PHA) production.

Otherwise, the medium for PHA production is tuned for the development of Pseudomonas putida, but not for the E.coli, so we had to test if this bacteria was able to grow in it. When we did this checking, we realized that the development of these bacteria did not occur in the PHA production media. However, with the addition of acetate (carbon source), the removal of the iron salt (added to the media to avoid the synthesis of a siderophore by Pseudomonas sp.) and, due to serendipity, with the double concentration of trace elementes, we got the media for the enteric bacteria growth.

Choosing the right fatty acid

Firstly, we tried to grow E. coli in the new PHA production media with different concentrations of octanoic acid. The same assays were done in parallel with P. putida in order to check which were the conditions where both microorganisms could grow and P. putida could produce enough quantity of bioplastic.

After overnight incubation, the cultures were washed using sterile PBS and ODs₆₀₀ were measured (Fig.4.). We also checked the PHA production by centrifuging the precultures, resuspending the pellet on PBS and adding Red Nile dissolved in DMSO, we could see the emission of fluorescence due to the interaction between the Nile red and the PHA through an UV transilluminator (Fig.5). By the results of the assays we chose to work with a 8mM concentration of fatty acids (Fig.4).

We also checked the PHA production by centrifuging the precultures, resuspending the pellet on PBS and adding Red Nile dissolved in DMSO, we could see the emission of fluorescence due to the interaction between the Nile red and the PHA through an UV transilluminator (Fig.5). By the results of the assays we chose to work with a 8mM concentration of fatty acids (Fig.4).

At this point we found that E. coli and P. putida could grow at 8mM of octanoic acid and that bioplastic (PHA) is also produced. However, because E. coli grows better in oleic acid and we wanted to check if P. putida could produce PHA if its phaC operon was induced by it, we grew both bacteria in different concentrations of octanoic and oleic acid but maintaining a constant concentration of fatty acids of 8mM. The assays done are explained in the table below (Fig.6).

We saw that E. coli had grown better with the increasing of oleic acid, getting at its maximum on experiment 9, even so, the quantity of pellet corresponding to 1 mL of preculture was scarce (and not visible at experiments 1 to 5). E. coli needed more time to grow in the PHA production media.

P. Putida had grown too, however we wanted to measure the production of bioplastic, we measured the ODs₆₀₀ from the precultures of P. putida by centrifugating 2 mL of them and then washing them on 1 mL of PBS and resuspending the pellet in 500 μl of PBS. Then, dilutions on PBS were adjusted to the lowest OD_600,corresponding to the experiment number 9 (8mM oleic acid). The growth of P. putida lower in PHA production media with a concentration of 8mM of oleic acid (Fig. 7-8).

The results showed that the growth of E. coli on 8mM of oleic acid was better than in any other condition, then experiment 9 conditions would be the best ones for the induction of clumping. However, even P. putida had produced bioplastic at all oleic acid concentrations, the highest production levels corresponded to experiment 1 conditions, which means in absence of oleic acid, just on 8mM of octanoic acid. Because of that, next assays were done following the conditions of experiment 1 and 9 (Fig.9).

After the optimization of the media, kinetics of the production of PHA and biomass generation were realized in relation to the time (Fig.10).

Pre-field test

Pre-field test

Final Test: PHA Production in an Heterogeneous Substrate (soil)

Finally, we designed an assay in which all the activities presented till this moment were carried out by the synthetic symbiosis that we have been working with. In this experiment we achieve the goal of our project: the detection of hotspots of interest in irregular substrates and the production of bioplastic (PHA) in those places. Our project works in a pre-field test!

A soil ground was prepared with an artificially distributed substrate-rich medium in discrete points (Fig.1). Once the medium was ready, we inoculated the soil with a C. elegans-Pseudomonas suspension and with transformed E. coli expressing the iRNA of interest. As a control, we took a picture of the soil ground the first day the microorganisms were added by exposing it to UV light (Fig.2). After a day we added Nile red to reveal the PHA production and to see if the experiment had finally worked (Fig. 3). It is possible to see bioplastic nodules which are red when combined with Nile red.

In addition, we took an electron microscopy image of one of the discrete points of medium (Fig. 4) to study what organisms were actually near the hotspots. More electron microscopy images were taken to demonstrate if C. elegans dragged Pseudomonas to the points of interest ( Fig. 4).

We finally were able to conclude that our synthetic consortium worked: Worms managed to reach the hotspots of interest, the worms dragged Pseudomonas with them and Pseudomonas finally made bioplastic detected be adding Nile red.

In addition, we took an electron microscopy image of one of the discrete points of medium (Fig. 4) to study what organisms were actually near the hotspots. More electron microscopy images were taken to demonstrate if C. elegans dragged Pseudomonas to the points of interest ( Fig. 4 [right] ).