Team:HokkaidoU Japan/Shuffling Kit/Examples


Revision as of 01:41, 29 October 2013 by Kwt (Talk | contribs)

Maestro E.coli

Shuffling Kit

Demonstrations for Usecase Example

We will show some interesting demonstrations of our kits, Promoter Selector and RBS Selector!

Promoter Selector

Let's select the best promoter for Kanamycin resistance by Promoter Selector.

For this demonstration we decided to use the expression of Kanamycin resistance. Changing the concentration of Kanamycin in agar plate, it is estimated that different promoter will be chosen by our Promoter Selector (fig.1).

If the concentration of Kanamycin was high, the colony with strong promoter would survive. Therefore, only one or two colors would appear and indicate the first and second biggest occupancy rate on the plate. If the concentration of Kanamycin was low, colonies with even weak promoters could be able to survive. So in this way many colors of colonies would appear (fig.2).

fig.1 Different promoter express each colors.
fig.2 Difference of Kanamycin concentration.


Optimum concentration of Kanamycin: in LB is 50 mg/ml
We prepared optimum and other 3 concentration plates.

  • Plate A: Kanamycin 125 mg per plate
  • Plate B: Kanamycin 250 mg per plate
  • Plate C: Kanamycin 500 mg per plate (optimum concentration)
  • Plate D: Kanamycin 1000 mg per plate

Gene Vector: pSB1C3

We cloned Kanamycin resistance gene from pSB3K3, by using BsaI adding primer. Used the Promoter Selector (K1084501, K1084502, K1084503, K1084504, K1084505 ).

Culture: 37 °C, for 48h


fig.4 Graph of number and rate, and table of number of colonies size over 1mm diameter.
fig.3 Picture of plate B (Kanamycine 250 mg). The colonies showed several colors.

After 48h cultivation, around 300 colonies had appeared on each LBKC (Kanamycin and Chloramphenicol) plates. We prepared LacZa expression in Promoter Selector system as negative control to estimate the success of Golden Gate Assembly. We got 0-7 blue colonies which was expressing LacZ alpha.

Mixed colored colonies which would have been transformed by two or more Promoter Selector were also observed. The number and rate of colonies per each plate were graphed (fig.4), with rejecting these undesirable colonies.

In fig.4, legend color corresponds to Promoter Selector’s part number. The sum of colony numbers is displayed above each bar, and rate is in these sections. Number in the table referrers the number of each Promoter Selector’s colony. These data are collected by n=!.


Big difference did not appear among each Kanamaicin concentration. In this experiment, number of colonies derived from K1084405 (containing K1084010 promoter) had the largest rate on each plate. This result suggests that the colonies which had K1084405 could cost little resource of transcription and translation for expression of Kanamycin resistance gene, and the rest of resource had been spared to cell growth. Thus, the number of colonies might be the largest. Otherwise, the DNA solution of K1084505 Promoter Selector used at ligation was simply larger than other DNA solution. Although the result is collected from only one time assay, higher concentration of Kanamycin and much number of trials than this time will be needed.

From these result and the experimental fact, the existence of Km resistance gene in Promoter Selector’s BsaI cloning section is partially confirmed. Our Promoter Selector was successfully assembled, but it does not adopted to all colonies. Then, as a result of assembling, we succeeded in making colorful colonies appear on one plate.

RBS Selector

4 colors

Let’s create all combinations by two reporter genes and make various colors on one plate!

The RBS Selector we made, can randomize the strength of RBSs in the operon. For a demonstration, we decided to create all combinations by two genes; mRFP1 (BBa_E1010) and LacZα (BBa_I732006) (fig.5). LacZα makes the colony blue. mRFP1 makes the colony red.

fig.5 Create all combinations by RBS of defferent stlength mRFP1 (BBa_E1010) and LacZα (BBa_I732006).

When the RBS of mRFP1 was stronger than that of LacZα, the colony would be red. When in the opposite case, the colony would be blue. And when the strengths of both RBSs were same, colony would be white or purple (fig.6).

fig.6 Each combinations of RBS make different colors.


  • Assembled promoter1 (BBa_K1084001), SD2 (BBa_K1084101), SD4 (BBa_K1084102).
  • Spread X-GAL(250 mg)on LBC plate.
  • Cultured at 37 °C for 26h.
fig.7 The colonies showed red, blue, white, and purple.


We got colorful colonies; red, blue, white, and purple.


We can say that our RBS Selector worked exactly!! The RBSs upstream of 2 genes were randomly assembled and they had different expression level.

64 colors