Team:Groningen/Project/Coating

From 2013.igem.org

(Difference between revisions)
Line 22: Line 22:
<ul>
<ul>
<li>
<li>
-
<u>A large, deep and circular bath</u></li>
+
<b>A large, deep and circular bath</b></li>
To contain enough volume for a large culture
To contain enough volume for a large culture
<br><br><li>
<br><br><li>
-
<u>Suitable growth medium for our <i>B. subtilis</i> strain</u></li>
+
<b>Suitable growth medium for our <i>B. subtilis</i> strain</b></li>
Perhaps with agar
Perhaps with agar
<br><br><li>
<br><br><li>
-
<u><a href="http://en.wikipedia.org/wiki/Water_aeration#Fine_bubble_aeration">Fine bubble aeration</a></u></li>
+
<b><a href="http://en.wikipedia.org/wiki/Water_aeration#Fine_bubble_aeration">Fine bubble aeration</a></b></li>
Bacillus is a very aerobic bacterium. This system facilitates thorough and gentle aeration. The small bubbles will diffuse enough when released from below the deep bath.
Bacillus is a very aerobic bacterium. This system facilitates thorough and gentle aeration. The small bubbles will diffuse enough when released from below the deep bath.
<br><br><li>
<br><br><li>
-
<u>A heated implant hanging inside and in the centre of the bath</u></li>
+
<b>A heated implant hanging inside and in the centre of the bath</b></li>
This is what we want to coat. As the implant is providing a temperature gradient, no heating of the medium is required, saving energy that would be spend on heating the entire bath.
This is what we want to coat. As the implant is providing a temperature gradient, no heating of the medium is required, saving energy that would be spend on heating the entire bath.
<br><br>
<br><br>
Line 100: Line 100:
</p>
</p>
 +
<h2>Procedure 2 - No heat motility</h2>
 +
<p>
 +
<br><u>Step 1</u><br>
 +
Initially the <i>B. subtilis</i> cells are grown in liquid medium (LB) at 37 °C until the culture is in the early exponential phase.
 +
This can be detected as the culture is rapidly increasing in number of cells, while the total number of cells is still relatively low.
 +
<br><br><u>Step 2</u><br>
 +
The cells are moved to the big volume of our setup, where the cells move around and grow further, though should still be in the exponential phase.
 +
<br><br><u>Step 3</u><br>
 +
Expression of the spider silk protein is stimulated by addition of IPTG to the medium.
 +
<br><br><u>Step 4</u><br>
 +
The implant is swirled through the medium, because the implant is coated with streptavidin the silk will automatically attach itself to the implant
 +
</p>

Revision as of 01:15, 5 October 2013

Coating

Overview

Applying the Coating to the implant is the end phase of our project. Here is an overview of what we would have up to this point:


With our engineered B. subtilis possessing all the desired genes and modifications, we would be able to put it to work in our coating setup.


Coating Setup

Our setup consists of the following components:

  • A large, deep and circular bath
  • To contain enough volume for a large culture

  • Suitable growth medium for our B. subtilis strain
  • Perhaps with agar

  • Fine bubble aeration
  • Bacillus is a very aerobic bacterium. This system facilitates thorough and gentle aeration. The small bubbles will diffuse enough when released from below the deep bath.

  • A heated implant hanging inside and in the centre of the bath
  • This is what we want to coat. As the implant is providing a temperature gradient, no heating of the medium is required, saving energy that would be spend on heating the entire bath.


Experimental setup for coating
Figure 1: A possible setup for coating


Remarks

Before going into the proposed procedures, it should be noted that this page covers aspects of our hypothetical situation. It is how we planned to proceed if the engineering of our B. subtilis would have been achieved earlier in our project. However, instead of assuming everything works as we intended, which would be the ideal situation, we have designed alternative procedures. These alternative procedures are adapted to the lack of a certain component, an assumption we make in our ideal situation, such as secretion of the spider silk protein.


Procedure 1 - Ideal situation


Step 1
Initially the B. subtilis cells are grown in liquid medium (LB) at 37 °C until the culture is in the early exponential phase. This can be detected as the culture is rapidly increasing in number of cells, while the total number of cells is still relatively low.

Step 2
The cells are moved to the big volume of our setup, where The cells move around and grow further, though should still be in the exponential phase. Influenced by the temperature gradient most cells should lose their ability to move near the implant. This results in accumulation of cells in the heated area close to the implant.

Step 3
Expression of the spider silk protein is stimulated by addition of IPTG to the medium. The secreted spider silk will attach to the implant.

Procedure 2 - No silk secretion


Step 1
Initially the B. subtilis cells are grown in liquid medium (LB) at 37 °C until the culture is in the early exponential phase. This can be detected as the culture is rapidly increasing in number of cells, while the total number of cells is still relatively low.

Step 2
The cells are moved to the big volume of our setup, where the cells move around and grow further, though should still be in the exponential phase. Influenced by the temperature gradient most cells should lose their ability to move near the implant. This results in accumulation of cells in the heated area close to the implant.

Step 3
Expression of the spider silk protein is stimulated by addition of IPTG to the medium. The secreted spider silk will attach to the implant.

Procedure 2 - No heat motility


Step 1
Initially the B. subtilis cells are grown in liquid medium (LB) at 37 °C until the culture is in the early exponential phase. This can be detected as the culture is rapidly increasing in number of cells, while the total number of cells is still relatively low.

Step 2
The cells are moved to the big volume of our setup, where the cells move around and grow further, though should still be in the exponential phase.

Step 3
Expression of the spider silk protein is stimulated by addition of IPTG to the medium.

Step 4
The implant is swirled through the medium, because the implant is coated with streptavidin the silk will automatically attach itself to the implant



Whole setup:(FRISO)
Spider Silk
Localizing the cells near the implant
Secretion or lysis approaches
Binding to streptavidin coated implant
Polymerization and sterilization


Old page silk secretion