Team:NJU China/Protocol
From 2013.igem.org
(Difference between revisions)
(Created page with "<html lang="en"> <head> <meta charset="UTF-8" /> <meta http-equiv="X-UA-Compatible" content="IE=edge,chrome=1"> <meta name="viewport" content="width=...") |
|||
Line 572: | Line 572: | ||
</div> | </div> | ||
<div class="ss-row ss-medium"> | <div class="ss-row ss-medium"> | ||
- | <div class="ss- | + | <div class="ss-right"> |
<h3> | <h3> | ||
<a>Subculturing Cells</a> | <a>Subculturing Cells</a> | ||
<span> | <span> | ||
- | Ready to passage when cell confluence to 80%, and the procedure is carried out in the super clean bench. | + | Ready to passage when cell confluence to 80%, and the procedure is carried out in the super clean bench.</br> |
- | 1.Remove present culture media. | + | 1.Remove present culture media. </br> |
2.Wash cells with PBS to remove the residual media. | 2.Wash cells with PBS to remove the residual media. | ||
- | 3. Add 2 mL of trypsin, and let the cells sit for 2-5 minutes at 37℃ until the cells separated from the culture dish. | + | </br>3. Add 2 mL of trypsin, and let the cells sit for 2-5 minutes at 37℃ until the cells separated from the culture dish. |
Note:It may be necessary to bang the culture flasks on the hood counter to remove any “sticky” cells from the flask surface. | Note:It may be necessary to bang the culture flasks on the hood counter to remove any “sticky” cells from the flask surface. | ||
- | 4. Immediately after the 2 minutes, add room temp DMEM media (10%FBS) to inactivate the trypsin, and passing the cell several times through a pipette. | + | </br>4. Immediately after the 2 minutes, add room temp DMEM media (10%FBS) to inactivate the trypsin, and passing the cell several times through a pipette. |
- | 5. Transfer cell suspension to 15 ml tube, centrifuge at 1000rpm for 5 minutes. Remove supernatant. | + | </br>5. Transfer cell suspension to 15 ml tube, centrifuge at 1000rpm for 5 minutes. Remove supernatant. |
- | 6. Add 5 mL of PBS, mix immediately by pipetting. centrifuge at 1000rpm for 5 minutes. Remove supernatant. Add DMEM to resuspend the cells | + | </br>6. Add 5 mL of PBS, mix immediately by pipetting. centrifuge at 1000rpm for 5 minutes. Remove supernatant. Add DMEM to resuspend the cells |
- | 7. Add cell culture medium DMEM to a new flask(or dish). | + | </br>7. Add cell culture medium DMEM to a new flask(or dish). |
- | 8. Add cell suspension into the new flask in a certain ratio (according to the result of counting, see Cell Counting), and mix it well. | + | </br>8. Add cell suspension into the new flask in a certain ratio (according to the result of counting, see Cell Counting), and mix it well. |
- | 9. Place culture flasks back into the 5% CO2 incubator and check daily | + | </br>9. Place culture flasks back into the 5% CO2 incubator and check daily |
- | Cell Counting | + | </br>Cell Counting |
- | 1. Add 5 μL of cell suspension into 45 μL PBS | + | </br>1. Add 5 μL of cell suspension into 45 μL PBS |
- | 2. Put 10 μL of the mixture onto the counting cell slide. | + | </br>2. Put 10 μL of the mixture onto the counting cell slide. |
- | 3. Count the cells in the four corner boxes and the middle box.Count border cells on only two of the borders (top and left or bottom and right etc.) | + | </br>3. Count the cells in the four corner boxes and the middle box.Count border cells on only two of the borders (top and left or bottom and right etc.) |
- | 5. The number of cells in the suspension = number of cells * 104/4 * dilution ratio per milliliter. | + | </br>5. The number of cells in the suspension = number of cells * 104/4 * dilution ratio per milliliter. |
</span> | </span> | ||
</h3> | </h3> |
Revision as of 14:21, 27 September 2013