Team:BGU Israel/Experiments

29.7.2013 Transformation of pkd78 to Electro-competent cells
The Electroporation standard protocol was used with the following data:

1. DNA volume - 1 uL.
2. cuvette width - 0.2 cm.
3. Time constant (Tao) - 5.5 msec.
4. Two LB agar plates with cmp were plated with bacteria - one with 20 uL of culture, the other with 50uL. The plates were grown overnight in 300c, and on both colonies grew.

31.7.2013 PCR amplification of GFP gene with lacI promoter
3 vials were made - one of them as a control vial.
A mixture was made, containing:

1. 51 uL DDW.
2. 15 uL KAPA HIFI buffer.
3. 2.25 uL of dNTPs.
4. 2.25 uL of forward primer.
5. 2.25 uL of reverse primer.
6. 1.5 uL of KAPA polymerase.

The mixture was divided into the 3 vials. DNA template was added to 2 of the vials (not to the control) - 0.3 uL of 102 ng/ml template solution.

1. The annealing temperature was set to 450C.

The vials were put in the PCR for 30 cycles. We used the protocol ”Routine high-fidelity amplification of longer DNA fragments is challenging due to the low processivity and lack of robustness of most proofreading DNA polymerases”.

1.8.2013 Recombineering protocol
In order to try and experience with the recombination system, BL21 pkd78 were made recombination – ready and transformed with a cassette containing only GFP gene and homologous recombination sites.
Changes from original protocol:

1. Centrifuge 10 min at 4200 g and resuspend pellet in 300 μL ice cold 10% glycerol. (final Vol. 1:100)

Transformation and selection:

1. Add up to 100ng of the purified PCR product cassette (1 μL) to 40 μL of competent cells. 3 min on ice.
2. Transfer the competent cells into an electroporation cuvette.
3. Electroporate with Ec2 setting. #1 cuvette-> 5.8m/sec. #2 cuvette-> 5.9 m/sec.
4. Plate 50 μL of culture on LB plates containing the appropriate antibiotic and/or selection agent. A serial of dilution was done, we use 10⁴ – 10⁸ to plate on the agar.
5. Cuvette #1 was add to LB agar + IPTG 1mM, incubated at 37^oC over night.
6. Cuvette #2 was add to LB agar + IPTG 1mM+CMP 50mg/ml, incubate at 37^oC over night, to confirm loss of pkd78.

2.8.2013
2 samples of BL21-Psup-Acetylizing syntethase were freezed (-80^oC)

4.8.2013
Goal: replacing antibiotic resistance

Components:

1. PkD 78
2. pET 15b
3. HiFi buffer X5
4. DDW
5. dNTP's
6. ampR FWD & REV primer
7. cmpR FWD & REV primer
8. kappa HiFi polymerase
9. DNA template
10. Gel Agarose

Amounts:

1. Control sample was prepared – containing all components except the template.
2. Each reaction was made twice.

PCR reaction:


Agarose gel has been prepared in order to get qualitative estimation about the components after the PCR.


The samples have background noise, thus additional agarose gel has been prepared, except now it is used to separate the pkD 78 backbone & the antibiotic resistance from the pET 15b.


5.8.2013 Colony PCR
Goal: Last week Adi transformed BL21 with a GFP cassette. We want to find colonies that have taken the cassette into their chromosome.

Colony PCR
The cassette is a linear DNA sequence not containing an origin of replication and no antibiotic resistance. So, we chose randomly 10 colonies from the plates in which the transformed BL21 were seeded and used their DNA as template for PCR with primers for the GFP gene.

1. Colony preparation – pick a colony and resuspend in 5 μl DDW PCR.
2. Boil for 5 min at 99^oC and immediately chill on ice (PCR program: colony_prep).
3. Use the 5 μl as template for PCR.

Amounts:

1. Control sample was prepared – containing all components except the template.
2. 10 samples were made – one from each colony.

PCR reaction:


Agarose gel has been prepared in order to get qualitative estimation about the components after the PCR:


Apparently, none of the selected colonies have not taken the cassette into the chromosome.

5.8.2013 Extraction of pkd78 bacbone and CRB gene from gel
Goal: PCR was performed by Alex on 4/08. Today we extract the DNA from the gel for further use.

Extraction of pkd78 and CRB resistance gene from agarose gel using QIAquick kit
1. Gel slice weight:

1. pkd78 – 151.1 μg ∼ 151.1 μl
2. CRB gene – 169.8 μg ∼ 169.8 μl

2. Added volume of QG Buffer:

1. pkd78 – 455 μl
2. CRB gene – 510 μl

3. Incubated for 10 min at 500c
4. Added volume of Isopropanol:

1. pkd78 – 151 μl
2. CRB gene – 170 μl

5. Centrifuge: 1 min, 13,400 rpm. Discarded flow through.
6. Added 500 μl QG Buffer.
7. Centrifuge: 1 min, 13,000 rpm. Discarded flow through.
8. Added 750 μl PE Buffer.
9. Centrifuge: 1 min, 13,000 rpm. Discarded flow through.
10. Centrifuge: 1 min, 13,000 rpm. Discarded flow through.
11. Added 35 μl DDW PCR.
12. Centrifuge: 30 min, 13,000 rpm.
13. DNA concentration:

1. pkd78 backbone – 36 ng/μl
2. CRB resistance gene – 19 ng/μl

Both placed in -200c, top shelf, pink box, 1D & 2D.

6.8.2013 Eantibiotic replacement of pkd78
Ligation of CRB gene to pKD backbone
1. The DNA fragments were digested by restriction enzymes. These following components have been inserted into 2 separate epindorphs:


conc. of CRB: 19 ng/μl         conc. of pKD: 36 ng/μl
Insert DDW first in order to lose less material.
2. Vortex and short spin.
3. Incubation at 37 for 15 min.
4. 10 min. at 80 degrees for inactivation of restriction enzymes.
5. Gel preparation: 1 gr Agarose, 50 ml TAE x1.
      5.1 Heat in microwave for 1 min.
      5.2 Cool the solution until it is warm and make sure it stays liquidly.
      5.3 Add two drops of Etidium Bromide
      5.4 Insert the gel into its facility and place the 30 well comb in its spot.
      5.5 Wait until the gel gets tough.
      5.6 Add TAE x1 until it covers the gel.
6. Insert the DNA fragments (30 μl) into the wells.
7. Insert marker lambda pST 6 μl to another well.
8. Turn electric potential to 90.
9. After 1.5 hr the bends were indentified and were extracted from the gel with the kit into 2 epindorphs with the DNA. QIAquick gel extraction kit (50)
10. Parameters for ligation:


11. Ligation mix (μl):


12. ligation was conducted by the Ligation protocol
13. Result:


7.8.2013 Transformation of BL21 pkd78 with pUC57 cI
Electrocompetent BL21 pkd78 were transformed by electroporation with pUC57 cI (τ=5.2 ms).
Transformed cells were incubated in 300c for 2 hours, plated on 2 crb & cmp LB agar plates, and grown overnight in 300c.
For negative control, untransformed BL21 pkd78 were also plated on crb & cmp plates.
After 2 days, colonies grew on both plates which were plated with transformed cells, and none grew on the plates plated with untransformed BL21 pkd78.

7.8.2013

1. The C1 plasmid arrived from hy-labs and was diluted. Final concentration - 50 ng\ul.
2. Transformation of puc57-cI to super compotent cells (dh5α) by heat shock.
3. Transformation of the pGFPuv into dh5α. This pGFPuv has undergone directed mutagenesis in order to add the stop codon.
4. Transformation of C.O (copper oxidase) into BL21 that contain the UAA incorporation tRNA and the acRS (acetyl lysine synthethase). The machinery was on pSUP.

8.8.2013 freeze bacteria
3 samples were frozen in -800c: pGFPuv 39 TAG, pSUP acRS PET15b – BL21, puc57-cI dh5α.S

11.8.2013

1. 2 starters containing: 10 ml (LB), 10ul (CRB 100), 10ul (cmp 50), pkD78 + C1
2. Kanamycin cassete has arrived.
3. kan cassete PCR from pkD4 plasmid ( T annealing= 52^oC).
4. pkD78-ampR assembly - digestion of PCR products with XbaI and Xhol (FD)
5. products were separated on agarose gel and extracted using gel extracting kit.

12.8.2013
            
            

14.8.2013
Transformation of BL21 pkd78 with kan cassette.
Starters have been prepared:

1. BL21 pkD78 + puc57-C1 +CRB100 (10ul) + CMP50 (10ul)
2. BL21 puc57-C1 +CRB100 (10ul)

15.8.2013 replacing antibiotic resistance
Goal: replacing antibiotic resistance
Components:

1. PkD 78 PCR product
2. CRB PCR product
3. HiFi buffer X5
4. DDW
5. dNTP’s
6. ampR FWD & REV primer
7. cmpR FWD & REV primer
8. kappa HiFi polymerase
9. DNA template
10. Gel Agarose

Amounts:

PCR reaction:


Agarose gel has been prepared in order to get qualitative estimation about the components after the PCR.
NO PCR Product was detected.
Transformation via Electroporation protocol:

1. Sample 1 – BL21 pkD78 (EC) -> puc57-CI (1ul)
2. Sample 2 – BL21(EC) -> puc57-Time Bomb (1.5ul)
3. Sample 3 – BL21 (EC) -> puc57-CI (1ul)

For all the samples Τ=5.56 m.sec (Electric shock)

Antibiotic plates prepared:

1. 2* CRB 100 CMP 50
2. 5* CRB 100
3. 3* KAN 30

16.8.2013 mutagenesis - cI to cI+his tag (second attempt)
We tried to use site directed mutagenesis on puc57 cI to create Puc57 cI+his tag.
A pcr vial was made:

1. 35 uL DDW
2. 10 uL HIFI buffer
3. 1.5 uL rev+fwd primer (cI +his tag)
4. dNTP 1.5 uL
5. 1 uL DNA template (cI plasmid)
6. 1uL KAPA polymerase.

The following protocol was used:

Cycling Parameters

Number of cycles


The PCR product were used for electroporation (Τ=4.9 msec)
The bacteria were then plated on 2 crb agar plates (20 ul, 50 ul) and incubated in 37^oC.

18.8.2013
BL21 pUC57 cI and Bl21 pUC57 TB were frozen in -800c.

19.8.2013 Mutagenesis - cI to cI+his tag
The last 2 attempts of site-directed mutagenesis failed. The PCR products of Stav's experiment (13/08/13) were ran on agarose gel. The results showed that the product was less than 300 bp - that indicates that the PCR failed.
My experiment from the 16th was conducted again with several changes - the primer's stock was made again, and the denaturation temperature of the DNA was raised to 99^oC, and this time, two exact PCR vials were made.

19.8.2013 Colony PCR
Colony PCR for: (using colony PCR protocol)

1. BL21 pkD78 + puc57-CI
2. BL21+ puc57-Time Bomb
3. BL21 + puc57-CI

5 starters have been prepared from the colonies on the kanMX cassette transformation plates.

22.8.2013 Starters
4 starterts were made from plates containing puc57-c1 His-tag.
2 starters were made from frozen stock of BL21 pkd78+ puc57 C1

26.8.2013 Bacteria with cI + his-tag lysis and separation
BL-21, puc57-cI w. cI+his tag culture after an over-night incubation w. IPTG induction (1mM) - was divided into 3 vials (10 mL each).
- The cultures waere centrifuged @ 4000 rpm for 15 mins - afterwards suspension was discarded.
- 2.5 ml of lysis buffer were added to all the vials (sediment was resuspended).
- 2.5 uL of benzoaze were added to each vial.
- 5 uL of protease inhibitor were added.
- 1.5 uL of 30 mg/ml lysosyme were added.
- 1 ml of bag-buster was added.
- all the vials were shaken for 20 mins and then centrifuged @ 4000 rpm for 25 mins.
- the lysate was filtered through a 45 um-pore filter.
- 3 nickel-colons were taken:
- washed with 6 ml DDW.
- the lysate was added, the fluids at this step were collected in vials labeled "Flow".
- 12 ml of wash buffer were added, the fluids at this step were collected in vials labeled "Wash".
- 4 ml of elution buffer were added, the fluids at this step were collected in vials labeled "Elution".

Results
The vials were used the next day in a follow up experiment.

27.8.2013 Mini Prep + enzyme restriction for TB cassette
Mini Prep + enzyme restriction for TB cassette
1. mini prep for DNA extraction were done for:
- pUC57 TB x2
- pUC57 cI x2
- pUC57 GK
DNA stored in -200c
2. In order to extract the TB cassette from pUC57, pUC57 TB was restricted with XbahI and BamHI.
3. The reaction didnt work (twice), probably because of the XbaI, which is probably not active. New enzyme will be ordered and we will do the reaction again.

Western for cI + His tag
1. For the western blotting we filled a 10 well gel with the following:

F - flow through
W - wash
E - elution
1,2,3 - 3 different colonies for the transformation

2. For the comassie we filled a 10 well gel with the following:


3. After the wells finished running on the gel, they were analyzed by the protocols: Western Blotting and Comassie.

Results:
There was no identification of cI-histag though there was a bend at the control well which signifies that the membrane blotting worked. For conclusion, the histag-cI mutagenesis didn't work.

comassie:


membrane after blotting:


control:


28.8.2013 Comassie Analysis on cI expression leak without IPTG
1. 3 vials were grown overnight:
      BL21 pUC57 cI histag + IPTG 1%
      BL21 pUC57 cI histag
      BL21 pUC57 cI histag + glu 1%
2. The vials were processed through protein extraction by lysis protocol.
3. The extraction, lysate, was loaded on a gel and ran for 1hr.
4. The gel was stained by comassie by the comassie protocol.

Results:


Conclusions:
1. The bends around 30 KDa suggest expression of cI though its not guaranteed. If so, there is a leak, but either way there is a very high rate of expression of cI which is a good thing.
2. The bend is much bigger with IPTG which shows that the promoter works fine. It is important to check the initial O.D. because each lysate has different amounts of protein.

31.8.2013 Comassie analysis for the lisate products made on 29.8
1. The lisate products were charged on the gel by the following order:


2. After they finished running on the gel, comassie staining took place by the comassie protocol Results:


Conclusions:
It was impossible to identify anything. Probably because the protein concentration in the lysate was too low.

31.8.2013 Comassie analysis on cI expression under various conditions
1. 6 vials were grown overnight
      1.1 BL21 pKD78 pUC57 cI + IPTG 1%, CRB100, CMP50
      1.2 BL21 pKD78 pUC57 cI + 1% glu, CRB100, CMP50
      1.3 BL21 pKD78 pUC57 cI + CRB100, CMP50
      1.4 BL21 pUC57 cI + IPTG 1%, CRB100
      1.5 BL21 pUC57 cI + glu 1%, CRB100
      1.6 BL21 pUC57 cI + CRB100
2. The vials were diluted 1:40 with the new LB in the same conditions and incubated until the O.D. reached 0.6.
3. The vials were processed through protein extraction by lysis protocol and comassie staining by comassie protocol.

Results:
No bands were noticed on the gel! A possible reason could be because there wasn't enough lysate in the first place because intentionally the bacteria grew to only O.D. 0.6 so there could be an analysis only on live bacteria and not dead ones but seems that it's not enough to analyze protein expression.

31.8.2013 PCR to amplify pKD78 backbone and CRB resistance
1. PCR by 4/8 protocol
2. The PCR products were loaded on Agarose gel by the following order:


Results:


The PCR didnt work at all! The primers were not good.

7.9.2013 Restriction of the P.A.S.E 1 cassette - preparation for tranformation
A plasmid containing the P.A.S.E 1 cassette (cI repressed promoter + holin + lysozime) was prepared for restriction in order to be transformed into bacteria.
A vial was made contining:
1) 13.5 uL DDW
2) 2uL FastDigest buffer
3) 2.5 uL DNA (180 ng/uL)
4) 1 uL FastDigest BamH1 enzyme
5) 1 uL FastDigest XbaI enzyme
(20 uL total).

The vial was kept in 37^oC for 15 mins, and then in 80^oC for 20 mins (enzyme deactivation).
The results were run on gel.

Results:
This experiment was conducted twice:
1- in the first time no DNA was spotted in the gel.
2- in the second time a bend that is >5 kbp was seen - meaning that the restriction failed.

7.9.2013 SDS-PAGE and staining of cI under different induction conditions
Bacteria with puc57-cI (IPTG-Arabinose promoter) were grown in 4 conditions:
1) no IPTG no Arabinose.
2) 1 mM IPTG, no Arabinose.
3) no IPTG no Arabinose. 0.6% glucose.
4) 1 mM IPTG, 20 mM Arabinose.
The bacteria cultures were lysed (following the same protocol from 29/08 in our notebook).
The lysis products were then separated by SDS-PAGE and stained (following the coomassie staining protocol).

Results:

8.9.2013 PCR amplification of 3 different templates
Three PCR vials were made, each containing:
- 10 uL Taq readymix buffer
- 7 uL DDW
- 1uL DNA template
- 1 uL forward primer
-1 uL reverse primer
(total 20 uL each).

The vials were:
1) To amplify the cI + Ara/lacI promoter - DNA template: pUC57 cI.
2) To amplify pkd78 backbone without the cmp ABR - DNA template: pkd78.
3) To amplify crb ABR - DNA template: pet15.

PCR program:
1) 5 mins @ 95^oC -
2) a) 20 sec @ 98^oC
   b) 30 sec @ 51^oC
   c) 2.5 min @ 72^oC
3) 5 min @ 72^oC

The results were ran on gel by Stav on the same day:
1.5% Agarose gel was made:


As can be seen pkd78 backbone amplification did not work, while crbR gene worked.
crbR gene was excised from gel and extracted using QIA quick gel extraction kit. Extracted DNA concentration: 7.5 ng/Μl

9.9.2013 PCR for pGFPuv
1. 4% agarose gel with lacI/AraC primers in order to purify it from mix (100bp).
2. Gel extraction by QIAGEN protocol.
3. PCR by the following amounts:




The cycling plan: (x18 cycles)


Results:
The PCR didn't work!

9.9.2013 crbR gene restriction
2 different stock of crbR gene previously amplified through PCR and puc57 GK cassette (from original stock) were used for restriction:

The mixture was incubated in 370c for 15 minutes, and then the reaction was inactivated by incubating in 800c for 20 minutes.
Restriction products were ran on a gel and extracted. DNA concetrations:

1. crbR 1 - 40 ng/μl
2. crbR 2 - 10 ng/μl
3. GK cassette - 17.5 ng/μl

GK cassette was used for transformation and sequencing:
BL21 pkd78 puc57 cI were previously induced with arabinose (for expression of recombination machinery) and IPTG (for cI expression) and washed to become electrocompetent. This culture was used for 5 transformations by electroporation with GK cassette previously restricted. IPTG was added to the SOC used after transformation to a final concentration of 1mM. Transformed cells were plated on kan LB agar plates.

Results:
No colonies grew. Later the sequencing results shown no match with GK cassette.

9.9.2013 Miniprep for pPGF-UV Purification
Insulation of plasmid PGF-UV from BL-21 using protocol from kit.

Result:

Vails stored in -20 C.

10.9.2013

1. DPN1 treatment was performed on the PCR products from the 9\9\13. and electroporation was performed on the products and grown on 2 plates (50ul, 150ul)
2. starter has been prepared from single colony - pkD78-amp + CRB100. - checking we have succeeded to replace the antibiotic resistance.

11.9.2013

1. one colony was taken from the plate made on the 10/9 in order to make a starter.
2. 2 starters of BL21, pkD78, amp50, 30^oC.
3. 2 starters of BL21, pkD78 + puc57-cI, cmp50, amp100, 30^oC.

12.9.2013
mini prep of BL21 pkD78 - 82 ng/ul.
preparation of compotent cells using recombineering protocol -

1. BL21 + pkD78
2. BL21 + pkD78 + puc57-cI

15.9.2013 Gradient_PCR - pull out the promoter
Reaction mixture:
      

Primers:
araC-Lac upstr
araC-Lac dnstr

Temp: 500c, 52.10c, 58.10c, 600c

1. 8 PCR tubes were prepared: 4 from puc57-cI sample, 4 from TB-cassette sample
2. 1 PCR tube was used as blank.

16.9.2013 Site-directed Mutagenesis
Mutant Strand Synthesis: using protocol Site-directed Mutagenesis
The sample reaction (X2 duplicate):

1. 10 μL of 5XKAPA HiFi Buffer
2. 1.5 μL of dNTP mix
3. 6.6 μL (125 ng) of Forward Primer + (125 ng) of Reverse Primer (primer is LAC1/araC , amplification PCR product at 8.9.13)
4. 1 μL (5-50 ng) of DNA template (template is pGFPuv from 9.9.13)
5. ddH₂O to final concentration 50 μL
6. Then add 1 μL of KAPA HiFi Polymerase.

Mutagenesis program- on protocol.
Products Stored in -20C.

17.9.2013 - Transformation of Mutagenesis product to DH5a by Heat shock
using super-competent DH5a cells .
In a sterile tubes (X2 duplicate):

1. 10μl of competent cells + 2μl of mutagenesis product incubate on ice for 30min.
2. Cells were transferred to water bath at 42C for 30sec and immediately back to ice for 2 min.
3. 200 μl of SOC medium was added.
4. Cells incubated at 37C for 1hr.
5. Plated X μl on CRB plates over night at 37C. (50 μl plate X2, 100 μl plate X2)

Control: same protocol done on competent cells without mutagenesis product.

18.09.2013 - Site directed mutagenesis (cI to cI +his tag) with new primers.
Two PCR vials were made, each containing:
- 33.5 μL DDW. - 10 μ KAPA HIFI buffer. - 1.5 μ of dntp's mix. - 1.5 μ FWD primer. - 1.5 μ REV primer. - 1 μ template DNA (puc57 cI). - 1 μL KAPA polymerase. (total of 50 μL).
Same PCR program was used as the experiment from the 16.08.
After PCR, 1.5 μL of DpnI was added to each vial and kept in room temperature for 1 hour (following the protocol from the 16.09 experiment - from step 2).
The DNA was ran on a gel. The two samples shown clear bands, indicating an amplification occurred. Proving the mutagenesis requires more steps.
The DNA was then transformed into BL-21 E.coli (using the electro-poration protocol):
Time constants
-5 msec in vial 1.
-5.1 msec in vial 2.
After incubation the bacteria were plated on crb containing agar plates.
Results
after an overnight incubation, no colonies were spotted.

19.9.2013 - PCR for amplification:
1. The following templates we used for PCR:
1.1 PKD4 for AMP & KAN extraction
1.2 pUC57 cI
1.3 PeT 15b cueo-His
1.4 pUC57-GK
1.5 pUC57-TB
1.6 pKD78

2. The Primers used for the PCR:


3. Reaction mixture and cycle program:
      
Polymerization time:
Reactions A,B,C,E,G - 45 seconds
Reactions D,F - 3 minutes

4. Results:
4.1 SFR gel:

4.2 normal gel:


5. PCR extraction
Other than the GK cassette and the pKD78 b bone, all the reactions worked and they were purified. Regarding the two that didn't, a possible reason could be that because the templates are very long (2000-5000bp) there should be a much longer extension time during the PCR reaction.


20.9.2013 - PCR to make cI his tag gene a biobrick: pUC 57 cI his tag generated by site directed mutagenesis (from 18/09 - 2 different samples) was used as a template to create a standard biobrick cassette to be inserted into psB1C3. The primers used are B his + stop F and B cI TU R.
Reaction mixture and cycle program:
      
PCR products were ran on a gel:

The marked bands correspond to ~800 bp, which is about the size of cI his tag with biobrick standard prefix and suffix.
The PCR products were purified using QIA quick PCR purification kit. Purified DNA concentration - 28 ng/μl.
The purified cI his tag was restricted with XbaI and pstI to become ready for ligation with a plasmid backbone. Reaction mix details:
DNA -11 μl
Buffer -2 μl
pstI -1.5 μl
XbaI -1.5 μl
DDW -14 μl
Reaction products were ran on agarose gel:

The marked band was excised from the gel and DNA was extracted using QIA quick gel extraction kit. Extracted DNA concentration - 1.000. Extraction did not work. We will try again tomorrow.

Making biobricks:

The DNA purified from yesterday's PCR products, detailed above, were restricted with XbaI and pstI to become ready for ligation with pSB1C plasmid backbone. Reaction mix details (all in μl):

The restriction products were ligated with pSB1C plasmid backbone. Ligation mix details:


Amplifying GK cassette and pkd78 backbone
Since these amplifications did not work yesterday, we repeated them with a different PCR program. Each reaction was done twice.
1. The following templates we used for PCR:
1.1 pUC57-GK
1.2 pKD78
2. The Primers used for the PCR:

3. Reaction mixture and cycle program:
      

4. Results:
Agarose gel showd no bands. PCR did not work again.

20.9.2013 - Site-directed Mutagenesis
1.Mutant Strand Synthesis: using protocol Site-directed Mutagenesis
The sample reaction (X2 duplicate):

1. 10 μL of 5XKAPA HiFi Buffer
2. 1.5 μL of dNTP mix
3. 2.5 μL (250 ng) of Reverse+ Forward Primers (primer is LAC1/araC , done by Alex at 16.9.13)
4. 1 μL (5-50 ng) of DNA template (template is pGFPuv from 9.9.13)
5. 35 μL ddH2O to final concentration 50 μL
6. Then add 1 μL of KAPA HiFi Polymerase.

Mutagenesis program- at protocol.

2. Dpn1 restriction:

1. 1.5 μL Dpn1 was added to mutagenesis product
2. Incubation at 37C for 1hr.

Products stored at -20C.

3.Transformation of Mutagenesis product to DH5a by Heat shock
using super-competent DH5a cells .
In a sterile tubes (X2 duplicate):

1. 10μl of competent cells + 2μl of restriction product incubate on ice for 30min.
2. Cells were transferred to water bath at 42C for 30sec and immediately back to ice for 2 min.
3. 200 μl of SOC medium was added.
4. Cells incubated at 37C for 1hr.
5. Plated Xμl on CRB plates over night at 37C. (50μl plate X2, 100μl plate X2)

Control: same protocol done on competent cells without mutagenesis product.
Incubation over night, 37C

21.9.2013
Result of Transformation:
no colonies have seen on plates.

Transformation of BL21 pUC57 cI with pUC57 GK:
In order to provide proof of concept for PASE1 (GK), 2 samples of electrocompetent BL21 puc57 cI were transformed with pUC57 GK by electroporation (time constants were both 5.70 ms). The SOC used contained 1 mM IPTG, and the transformed cells were plated on crb+kan plates with 30 μl 100 mM IPTG.

Back Bone digestion- PSB1C3

1. digestion with restriction enzymes PstI and XbaI.
2. Running restriction product in 2% agarose gel for B.bone extraction.
3. QI Aquik gel extraction kit for purifying DNA from gel. (nanodrop: con. 16ng/ul)
4. Ligation of the purifying B.Bone product with: cI T4, TB cassette, His tag+stop codon, KanR and, AmpR. (incubation for 1hr, 33C. stop reaction in 80C)
5. Transformation by electroforetion to BL-21, incubation over night.