Team:Dundee/Project/SoftwareTheory

From 2013.igem.org

(Difference between revisions)
Line 92: Line 92:
</div>
</div>
-
<div class="row" >
 
<h2> Deployed in Clatto </h2>
<h2> Deployed in Clatto </h2>
Line 101: Line 100:
<center><img src="https://static.igem.org/mediawiki/2013/e/e6/Moptopus2.jpg" width="100%"></img</center>
<center><img src="https://static.igem.org/mediawiki/2013/e/e6/Moptopus2.jpg" width="100%"></img</center>
</div>
</div>
-
</div>
+
 

Revision as of 15:35, 1 October 2013

iGEM Dundee 2013 · ToxiMop

Platforms and Communication
In order to use the sensors and detectors mentioned before, the moptopus was created using two main control boards: the Raspberry Pi (Model B) and an Arduino (Mega 2560).





A Raspberry Pi (http://www.raspberrypi.org) is a low cost, low power computer system which can fit in the palm of your hand. It has no onboard storage and instead runs various distributions of linux via insert-able SD Cards. The Raspberry Pi was chosen for our project due to its low cost and power requirements and the ability to easily program on it.

We implemented a Raspberry Pi as the control centre of the Moptopus. It carries out some information processing and controls the flow of information to any users. It is able to connect to the internet and allow a user to control the Moptopus while in operation. Our Raspberry Pi runs the Rasbian operating system (http://www.raspbian.org).

An Arduino (http://www.arduino.cc) is a cheap microcontroller, able to control and read voltages from metal pins which are connected to it. The digital and analogue input/output pins on our Arduino Mega have been used to control modules such as an LCD screen, light sensors, temperature sensors and the dissolved oxygen and pH sensors.

A number of methods of communication between the Raspberry Pi, Arduino and internet have been used. The Raspberry Pi is able to request data from a specific sensor by use of some of its own onboard pins. The configuration we used is called an I2C bus which is a serial communication method requiring just two pins on the Raspberry Pi and Arduino to communicate. Using this I2C bus, the Raspberry Pi asks the Arduino to take a specific measurement using one of the sensors.
The Arduino is also equipped with an Ethernet shield allowing it to be connected to the Ethernet port aboard the Raspberry Pi. This allows the streaming of data from the Arduino to the Pi. Finally, the Raspberry Pi has an added USB Wi-Fi device for connection to a local wireless network. This allows the Raspberry Pi to be communicated with and remotely logged into.

Sensors

Light

The sensors used to detect light were simple and cheap Light Dependent Resistors (LDRs). The specific LDRs used were Excelitas Tech – VT90N1. These light sensors were implemented in the moptopus in order to monitor the intensity of light falling on the lake on a day to day basis.


Temperature and Humidity

A combined temperature and humidity sensor was implemented to sense at the surface of the water with high accuracy. The sensor used was a SHT71, which provided temperature and humidity measurements to 2 decimal places. According to the datasheet for the sensor, the typical error present in these measurements was ±0.4% for temperature and ±3% for humidity.


pH

The pH of the fresh water is of significance when determining whether an algal bloom is likely to break out and also has implications on the toxicity of the algal bloom. The pH sensor used was a silver/silver chloride probe produced by Atlas Scientific. This was accompanied by a data stamp via which communication with the Arduino system was possible.


Dissolved Oxygen

The dissolved oxygen concentration of a water body is significant in determining whether algal bacteria can grow in an explosive manner. Furthermore, it can also help detect the breakdown of cyanobacteria after an algal bloom. Thus, a dissolved oxygen sensor and accompanying stamp by Atlas Scientific was implemented and built into the Moptopus.


Onboard camera

The Moptopus was fitted with an onboard camera in order to view its surroundings. The camera selected was a Logitech C310 HD and this was mounted on the top of the Moptopus. By allowing a user to view the surroundings of the Moptopus, the conditions of the lake at any time can be viewed. The potential for such viewings would be to allow the monitoring of aspects such as the amount of waste rubbish which has been discarded into the water reservoir. Such waste can provide cyanobacteria with nutrients required for growth. Furthermore, should an algal bloom occur viewing of the site could allow for a monitoring of the growth pattern of the algae and in such a fashion be informative to potential action to reduce the likelihood of future algal blooms.


Deployed in Clatto