Team:KIT-Kyoto/nf08123

Protocol

Miniprep

Solution Ⅰ (50 mM Tris-HCl and 10 mM EDTA, and 50 µg/mL RNase A, pH 8.0 (25˚C))

Solution Ⅱ (0.2 M NaOH and 1 % SDS)

Solution Ⅲ (4 M guanidine hydrochloride and 0.5 M potassium acetate, pH 4.2)

Solution Ⅳ (5 M guanidine hydrochloride, 20 mM Tris-HCl, and 38% ethanol, pH 6.6 (25˚C))

Solution Ⅴ (2 mM Tris-HCl and 80% ethanol, pH 7.5 (25˚C))

Pick up a single colony from plate and cultivate it overnight in 3ml LB medium containing appropriate antibiotic at 37˚C˚.

↓

Transfer the culture into a 1.5ml tube, centrifuge at 13,000 rpm for 1 minute, and discard the supernatant (2 times).

↓

Add 250 µL of SolutionⅠ to the pellet and mix well with vortex.

↓

Add 250 µL of SolutionⅡ and mix well by turning the tube upside down several times.

↓

Add 350 µL of SolutionⅢ and by turning the tube upside down several times.

↓

Centrifuge at 13,000 rpm for 5 minutes.

↓

Transfer the supernatant (approx. 850µL) to a mini prep column.

↓

Centrifuge at 13,000 rpm for 1 minute and discard the flow-through.

↓

Add 500 µL of SolutionⅣ.

↓

Centrifuge at 13,000 rpm for 1 minute and discard the flow-through.

↓

Add 700 µL of SolutionⅤ.

↓

Centrifuge at 13,000 rpm for 1 minute and discard the flow-through (2 times).

↓

Set the column on a new 1.5ml tube and add 100 µL of nuclease-free water.

↓

Centrifuge at 13,000 rpm for 1 minute and collect plasmid DNA.

Rapid check of the insert by colony cracking

Add 45 µL of cracking solution(3% w/v SDS ,50mM Tris -base ,pH12.6) into each tube.

↓

Suspend a small quantity of the colony in a tube using a sterilized toothpick.

↓

Incubate the tube at 65°C for 10 minutes.

↓

Add a drop of 10x Loading Buffer.

↓

Add equal volume of phenol/chloroform.

↓

Mix with vortex.

↓

Centrifuge at 13,000rpm for 3 minutes.

↓

Apply the supernatant to 1% agarose gel electrophoresis.

↓

Stain the gel in ethidium bromide solution for 10 minutes.

↓

Plasmid DNA can be detected by UV-illuminator as a band between genomic DNA band and low molecular size RNAs.

DNA purification and precipitation

Mix 350 µL of sterilized water and 50 µL of 3 M sodium acetate with DNA sample.

↓

Mix DNA solution with equal volume of phenol/chloroform by vortex.

↓

Centrifuge at 13,000 rpm for 5 min, then transfer the supernatant into a new tube.

↓

Add equal volume of 2-propanol, and mix by turning the tube upside down.

↓

Centrifuge at 14,500 rpm for 10 min at 4˚C.

↓

Carefully decant the supernatant.

↓

Add adequate volume of 70 % ethanol.

↓

Centrifuge at 14,500 rpm for 5 min at 4˚C.

↓

Carefully decant the supernatant.

↓

Dry in the desiccator under vacuum for 5 min.

↓

You can get dried DNA pellet.

PCR

Adjust the concentration of each primer to 100 pmol/µL with sterilized water.

↓

Mix 10µL of forward and reverse primer solutions with 80 µL H2O in a new tube (final primer concentration is 10 pmol/µL).

↓

Use 1 µL of primer mix for PCR.

Recipe for PRC is as follows:

SDS polyacrylamide gel electrophoresis (SDS-PAGE)

12.5% separation gel (recipe for a sheet of gel)

Isolation and purification of DNA bands

Ligation

Transformation