Team:ETH Zurich/Experiments 5

From 2013.igem.org

Revision as of 02:07, 5 October 2013 by Niederbm (Talk | contribs)

Header2.png
80px-Eth igem logo.png

Contents

High pass filters

The detection of different OHHL levels depending on the number of mines requires filters in our detection system. We decided to create a high pass filter library by doing site directed mutagenesis of the wild type [http://parts.igem.org/Part:BBa_R0062 BBa_R0062 PluxR]. The sites for mutagenesis were chosen from literature (2) (see Figure 1).
We were able to isolate a promoter having a lower expression level and being less sensitive than the wild type promoter (Figure 2). The promoter is called [http://parts.igem.org/Part:BBa_K1216007?title=Part:BBa_K1216007 PluxR variant BBa_K1216007] (G1, according to its initial position in the deep well plate).
Those two different promoters were used to create two high pass filter to detect different OHHL concentrations. The two promoters were analyzed not only in liquid culture by 96-well plate assays and single cell analysis (FACS) but also for E.coli on agar plate. Interestingly the EC50 sensitivity (half maximal effective concentration, EC50) is different between cells in liquid culture and cells on agar plates.


Site directed saturation mutagenesis PCR of the BBa_R0062 PluxR

Figure 1: Promoter mutation sites The wild type promoter from the biobrick BBa_R0062 was mutated using site directed saturation mutagenesis. The library shows the targeted sites for site directed saturation mutagenesis. The sequences for the library, the BBa_R0062, the BBa_K1216007 and the wild type luxR promoter from literature(2) are given. All assays were carried out in duplicates, results are presented as mean ± standard deviation.

We did site directed saturation mutagenisis of specific sites of the lux box according to the results taken from literature (2) (see Figure 2).
We mutated the promoter directly in the BBa_J09855 construct and cloned it into a eGFP gene as a reporter to be able to screen for differences in the dose response curves. In the end we isolated one mutated promoter which shows a shift in sensitivity (see section below)


Fluorescence data analysis

Formulapluxr1.png

The fitting of the following graphs was performed using this equation :

Output = eGFP levels [au]
Top = maximal eGFP level [au]("full induction")
Bottom = minimal eGFP level [au](“leakiness”)
n = Hill coefficient (“cooperativity”)
EC50 = Half-maximal effective concentration (“sensitivity”)
[AHL]=OHHL concentration [nM]


Native OHHL tests using microtiter plates

Figure 2: Sensivity curve of the wild type promoter and G1 mutant. The OHHL concentration range is plotted against the standarized fluorescence (au).
For the wild type : EC50=5.86 nM, R2= 0.87,n=1.7
Fore the G1 mutant: EC50=1'341 nM, R2= 0.98,n=0.8. All assays were carried out in triplicates, results are presented as mean ± standard deviation.


In order to select mutated luxR promoters we need to know about the sensitivity. Thus, we carried out dose response cruves using the Tecan Infinite M200 plate reader. The test range was inspired from literature (1).

The results are shown in Figure 2.


Dose response curves of luxR promoters under single cell analysis

Liquid culture and agar plate OHHL detection comparison

Here we employed single cell flow cytometry to obtain high quality fluorescence data of each promoter under different OHHL concentrations.we started by analyzing cells grown in liquid culture, then we shifted to agar plate format in order to fit to our project. We obtained different EC50 values between cells in liquid culture and in agar plates for each luxR promoter (see Figure 3, 4 and 5). See methods for the protocol


Figure 3: Sensitivity curve of the wild type BBa_R0062 on agar plates and liquid culture For the liquid culture we got :EC50=0.02 nM nM, R2=0.84, n=1.7; For the agar plates we got :EC50=4.45 nM, R2=0.80, n=1.7. All assays were carried out in duplicates, results are presented as mean ± standard deviation.
Figure 4: Single cell data of the wild type BBa_R0062 promoter vs. the pluxR mutant The histogram plots of eGFP levels for each tested OHHL concentration, culturing condition and corresponding promoter. In orange experiments on agar plates. In black experiments in liquid cultures. On the top the data of the wild type luxR promoter. On the bottom the data of the luxR promoter variant. All assays were carried out in duplicates, results are presented as mean ± standard deviation.

[[File:G1_plate.png|400px|left|thumb|Figure 5: Sensitivity curve of the G1 (pluxR variant BBa_K1216007) on agar plates and liquid culture
For the liquid culture we got: EC50=6482 nM, R2=0.97, n=0.8;
For the agar plates we got :EC50=12'555nM, R2=0.93, n=0.8. All assays were carried out in duplicates, results are presented as mean ± standard deviation.]


In liquid culture

The direct plot of both sensitivity curves (Figure 6) shows the shifted sensitivity of the luxR promoter in comparison to the wild type BBa_R0062 promoter. The EC50 shifted from 0.02nM for the wild type BBA_R0062 to 6'250 nM for the luxR variant promoter which is equal to a 300'000 fold increase.


Figure 6: Comparison of the Wild Type pluxR and the pluxR mutant sensitivity curves in liquid culture using the BD LSRFortessa™ Flow Cytometer System
For the wild type :EC50=0.02nM, R2=0.84, n=1.7
For G1 we got :EC50=6482nM, R2=0.97, n=0.8. All assays were carried out in duplicates, results are presented as mean ± standard deviation.


On agar plates

The direct plot of both sensitivity curves (Figure 6) shows the shifted sensitivity of the luxR promoter in comparison to the wild type BBa_R0062 promoter. The EC50 shifted from 4.45 nM for the wild type BBA_R0062 to 12'555 nM for the luxR variant promoter which is equal to a 2800 fold increase. Therefore, comparing with the results from cells growing in liquid culture an increase of 220 and 2 times for wild type BBa_R0062 and pluxR variant respectively. If you want to know more about the methods please click here

Figure 7: Comparison of the sensivity of the wild type promoter and the mutated luxR promoter on agar plates
For the wild type we got :EC50=4.45 nM, R2=0.80, n=1.7
For the pLuxR variant we got :EC50=12'555 nM, R2=0.93, n=0.8. All assays were carried out in duplicates, results are presented as mean ± standard deviation.


Rational design of additional luxR variants with partial sensitivity recovery based on the G1 mutant

According to initial model predictions confirmed by successive experimental validation the G1 promoter sensitivity is too low to drive a significant response in the concentration gradient established by our sender cells.
We need a collection of promoters with a set of EC50 values between the wild type and G1 itself. Since G1 has been obtained through two random mutations: 4T>A and 16C>G reverting one of the two, we reasoned, should result in a LuxR binding strength closer to the wild type. To test this hypothesis we ordered oligos encompassing all the possible combination of single position mutants (See list) and plan to experimentally characterize, and eventually deposit in the registry, all the resulting pLux variants. In parallel we used degenerate oligos to generate a small library (16 members) containing all the combination of double mutants for the two G1 key position to verify if all the double mutants show similar EC50.

References


(1) M Geske G.D.,Evaluation of a focused library of N-aryl L-homoserine lactones reveals a new set of potent quorum sensing modulators.
(2) Luis Caetano A Mutational Analysis Defines Vibrio fischeri LuxR Binding Sites