Polyurethane (PUR) Degradation Module

Introduction

Both efficiencies of Polyurethane (PUR) degradation and ethylene glycol production are important for the performance of MAPLE system. We built a mathematical and deterministic model that is based on MATLAB extension Simbiology for Polyurethane degradation. The model contains the kinetic property of degradation enzymes that is helpful for the design of assays. As we scaled up the initial concentrations of all substrates to meet the conditions for a bio-reactor, the model can provide preliminary simulations and predictions for the MAPLE system.

Design

Objective

Here are some specific objectives for the model to achieve:

1. The model should contain the gene expression model of the degradation enzymes because the enzyme concentration determines the rate of plastic degradation. In our case for PUR degradation, we used [http://parts.igem.org/Part:BBa_K206000 pBAD strong promoter K206000] for most enzymes. We built the gene expression model based on inducible pBAD promoter, which gene expression rate can be regulated by inducer concentration.

2. The model should show the efficiency of the enzyme secretion to the culture from the cells. It's also important because the enzyme concentration in the culture depends on it. Here we used pelB secretion tag for most enzymes in order to achieve a high efficiency.

3. The model basically predict how long will take to degrade a known concentration of soluble polyurethane. It is assumed that the enzyme in our assays has the same kinetic properties as the enzyme used in the literature. The model can suggest a suitable concentration of the plastic to use in order to get good results from the assays.

4. It is known that ethylene glycol is toxic to E.coli. However, it has no clear effect on the growth of our MG1655 strain when the concentration of ethylene glycol is below 200mM. Therefore, the model should suggest a safe range of PUR concentration to avoid a high concentration (>200mM) of ethylene glycol produced.

The Model

Polyurethane (PUR) degradation involves 5 different degradation enzymes:

However, 4 of the 5 enzymes are not well characterised before, so we could't find enough kinetic data from the literature. The only well-characterised PUR degradation enzyme PudA is used in the model as an illustration of all PUR degradation enzymes. The model will be more complete when the kinetic data of the other enzymes are defined. The finished PUR degradation model is shown as below:

Key

There are two compartments which represents cells and the culture from left to right. The "cell" compartment contains the gene expression module whereas the "culture" compartment contains the degradation module. The "secretion" block that connects two compartments is the secretion module.

Parameters and assumptions

Gene expression module of PudA

1.Derivation of the maximal expression rate,β

• Average molecular weight (Mw) of a base pair = 660g/mol[http://www.geneinfinity.org/sp/sp_dnaprop.html][http://www.lifetechnologies.com/uk/en/home/references/ambion-tech-support/rna-tools-and-calculators/dna-and-rna-molecular-weights-and-conversions.html]
• Average mass of a base pair = 660g/mol x 1.66x10^-24 = 1.1x10^-21g
• Volume of an E.coli cell = 1µm³[http://kirschner.med.harvard.edu/files/bionumbers/fundamentalBioNumbersHandout.pdf] = 1x10^-15L
  • ∴Mass concentration =
  • ∴Molar concentration of 1 base pair in the volume of E.coli = = 1.66x10^-6 mM
• BioBrick assembly plasmid pSB1C3 is a high copy number plasmid (100-300 copies per cell)[http://parts.igem.org/Part:pSB1C3?title=Part:pSB1C3]
  • assume 200 copies per cell
• ∴ concentration of the gene per cell = N x 200 x 1.66x10^-6mM, where N = number of base pairs
  • ∴ concentration of the gene BDH2 (N = 768) in the volume of an E.coli cell is = 0.25mM
• Transcription rate in E.coli = 80bp/s[http://kirschner.med.harvard.edu/files/bionumbers/fundamentalBioNumbersHandout.pdf] = 80 x 1.66x10^-6mM/s = 80 x 1.66x10^-6 x 60mM/min = 7.97x10^-3mM/min
• ∴ Rate of mRNA_BDH2 production under the control of pBAD = 7.97x10^-3 ÷ 0.25 = 0.032/min

• Average molecular weight(Mw) of an amino acid(aa)= 110g/mol[http://www.genscript.com/conversion.html][http://www.promega.com/~/media/Files/Resources/Technical%20References/Amino%20Acid%20Abbreviations%20and%20Molecular%20Weights.pdf]
• Average mass of an amino acid = 110g/mol x 1.66x10^-24=1.83x10^-22g/L
  • ∴Mass concentration of one aa in the volume of an E.coli = = 1.83x10^-6g/L
  • ∴Molar concentration of one aa = = 1.66x10^-5mM
• Translation rate = 20aa/s = (20 x 1.66x10^-5 x 60)mM/min = 0.020mM/min
• BDH2 comprises of 256aa[http://www.uniprot.org/uniprot/Q2PEN2&format=html]
  • ∴concentration of BDH2's aa in the volume of an E.coli = 1.66x10^-5mM x 256 = 4.25x10^-3mM
• ∴ Rate of protein production = 0.020 ÷ 4.25x10^-3 = 4.7/min

PUR degradation module

The reaction equation of the PUR degradation is:

[Polyurethane]+[PudA]= 5 [ethylene glycol] + 5 [polyisocyanate] + [PudA]

Assumptions:

We assumed 1 mole of polyurethane dispersion can produce 5 moles of ethylene glycol.

The molecular weight of a single polyurethane monomer is 470 g/mol whereas the molecular weight of the polyurethane dispersion is around 2000 g/mol.[http://www.polyurethanes.basf.de/pu/solutions/en/content/group/Arbeitsgebiete_und_Produkte/Grundprodukte/Lupraphen-Produktuebersicht_Gewicht]Therefore, the short-chain polyurethane consists approximately 5 monomers. 5 molecules of ethylene glycol will be produced by degrading one chain of polymer.

We also assumed a simple Michaelis-Menten mechanism for PudA

The parameters for the kinetic equations are:

The efficiency of Secretion is assumed to be 90% secretion over 2 hours.[http://www.ncbi.nlm.nih.gov/pmc/articles/PMC1251600/] The rate of secretion in the model is therefore:

rate of secretion = 0.9[concentration of PudA]/120 (mM/mins)

Simulations and Results