Team:TU-Eindhoven/LabJournal

From 2013.igem.org

Revision as of 18:47, 22 August 2013 by ArdjanvanderLinden (Talk | contribs)

Introduction

random text
Here you are, Ardjan!

Week 1

24 July
2013

Contents

Creating agar plates

Before any real lab work could begin some supplies had to be created, including a selection of agar plates. We needed two different types of agar plates, some with ampicillin antibiotics and others with kanamycin antibiotics. To manage this we created 2 separate agar solutions, a 200mL mixture for the ampicillin plates and a 400mL mixture for the kanamycin plates. The protocol we followed for the creation of the agar solutions was as follows:

  • Mix together the following amounts to create 200mL agar solution:
    • 2g Peptones
    • 2g NaCl
    • 1g Yeast extract
    • 3g Agar
    • Fill the container up to 200mL with demineralised water.
  • For a 400mL solution mix together:
    • 4g Peptones
    • 4g NaCl
    • 2g Yeast extract
    • 6g Agar
    • Fill the container up to 400mL with demineralised water.
  • Next the containers were autoclaved and allowed to cool, but not harden.
  • The following steps were all performed in the vicinity of a blue flame to ensure a sterile working environment.
  • Before pouring the plates the correct antibiotics were added. The concentration of the ampicillin antibiotics was 100ng/µL and that of the kanamycin antibiotics was 30ng/µL.
  • The solutions were now ready to be poured into agar plates. From the solutions we made we were able to pour 8 ampicillin plates and after receiving a little extra (about 350mL) kanamycin agar solution we poured a total of 27 kanamycin plates.
  • The plates were cooled on the bench and allowed to harden before being stored in a 4°C refrigerator.

Transforming the DNA

At this moment in time only one DNA vector (Protamine-1-Optimized) had arrived, but being impatient and rearing to go we decided to proceed with this one sample anyway which also allowed us a chance to get back into the rhythm of doing lab work. We needed to transform the 4µg of DNA into NB bacteria ready for plating and culturing. This all was done by completing the following steps:

  • The first step was to dilute the 4µg of vector in 20µL of MilliQ water. This created a 200ng/µL solution.
  • Of the previously created solution 1µL was pipetted into 199µL of MilliQ water creating a 4000 times dilution (1ng/µL).
  • Of this 1ng/µL solution 1µL was pipetted into 20µL of NB bacteria. The two dilutions could now be stored in the -20°C freezer.
  • The NB/Vector solution was left on ice for a short while before being heat-shocked in a water-bath of 42°C for 30 seconds.
  • Now the NB bacteria were returned to ice for 2 minutes.
  • After allowing the bacteria to cool 80µL of SOC solution was added. Hereafter the NB bacteria were not returned to ice. Instead they were placed in a 37°C incubator for 60 minutes.

Plating the bacteria

After incubating the bacteria for a hour they were ready to be plated so that we could create a number of cultures. This was done in the following fashion:

  • The following steps were all performed in the vicinity of a blue flame to increase the sterility.
  • The plate was opened and the entire bacterial solution (approx. 101µL) was pipetted onto an ampicillin agar plate.
  • To ensure even culture growth the solution was spread out over the plate using a sterile spreader.
  • The plate with its bacterial spread was then placed in a 37°C incubator and left there overnight to grow.

Making LB medium

Another preparational step that was performed was the creation of LB medium which we will be using a lot in the coming weeks. The protocol for the making of LB medium follows that for the creation of agar solution without the addition of the agar. So to create 1L of LB medium we mixed the following:

  • 10g Peptones
  • 10g NaCl
  • 5g Yeast extract
  • Fill the container up to 1L with demineralised water.
  • The entire container was then placed in the autoclave and sterilized.
  • The LB medium was allowed to cool and has been stored for later use at room temperature.

25 July
2013

Creating small cultures

Today we continued with the Protamine-1-optimized sample. This sample had been plated onto an ampicillin agar plate and was allowed to grow overnight. The next step was to transfer cultures from this agar plate into small amounts of LB medium so we could obtain a slightly larger culture, essentially increasing the amount of viable DNA vectors we have. The transformation to LB went as follows:

  • All following steps were performed in the vicinity of a blue flame increasing the sterility.
  • Firstly three small falcon tubes were filled with 8mL of LB medium.
  • To each of the falcon tubes 8µL of ampicillin antibiotics were added.
  • Now the agar plate was opened and three free lying colonies were chosen for picking. Each of the chosen colonies was then picked by lightly scraping across it with a pipet point. Each pipet point and colony picking was then ejected into one of the falcon tubes.
  • The falcon tubes were then placed into a rotating incubator set to 37°C and left there to culture overnight.


As there were no further preparational steps to perform and no other DNA vectors had arrived this concluded a rather short day in the lab.

26 July
2013

DNA Retention from cultures

Previously (on the 25th July 2013) three small 8mL cultures had been placed in the incubator containing NB bacteria which housed the vector for the protamine-1-optimized sample. These cultures had grown overnight and it was our aim today to retain the DNA vectors from these three cultures, essentially having allowed us to multiple the amount of DNA we had available. To perform this DNA retention a miniprep protocol was followed as is described below:

  • First the culture tubes were spun down in a centrifuge for 10 minutes at 3700rpm causing the bacterial cells with the DNA inside to form pellets isolating it from the growth medium.
  • The supernatant that had formed above the pellets was discarded and the pellets themselves were resuspended in 250µL of P1 buffer. The tubes were gently shaken by hand until the entire pellet had resuspended.
  • The suspension was then transferred by means of pipetting into a smaller (1.5mL) eppendorf tube.
  • 250µL of P2 buffer was then added to the eppendorf tube and the solution was inverted by hand until it had turned a clear blue.
  • Within 5 minutes of adding the P2 buffer 350µL of N3 buffer was added to the solution and the eppendorf tube was inverted again until the solution was clear again.
  • Once clear the eppendorf tube was placed in the centrifuge and spun for 10 minutes at 13000rpm seperating the bacterial cells from the DNA which remained suspended in the solution. The bacterial cells formed a pellet in the bottom of the eppendorf tube. (Unfortunately the pellet had not completely formed after 10 minutes so the eppendorf tube was spun for a further minute, again at 13000rpm.)
  • As soon as the centrifuge had stopped and we could see that the pellet had properly formed, the supernatant was poured off into a special QIAcolumn. The pellet could be discarded in the bio-hazard waste.
  • The QIAcolumn was subsequently centrifuged for one minute at 13000rpm, during which the DNA vector bound to the column meaning the flow through could be discarded.
  • 750µL of PE buffer was then added to the QIAcolumn before centrifuging it for another minute at 13000rpm. The flow through was discarded.
  • To ensure that all the PE buffer had passed through the column it was then spun yet again for one minute at a speed of 13000rpm. Yet again the flow through could be discarded.
  • The column itself was then placed above a sealable 1.5mL eppendorf tube so that the DNA could be contained and stored. To obtain the DNA from the column 50µL of MilliQ water was pipetted onto the very center membrane of the column after which it was spun down for one minute at 13000rpm. The flow through now sat in the 1.5mL eppendorf tube and contained the DNA vectors.

Nanodrop Test

To check how much DNA we had acquired by culturing the NB bacteria with our vector a small nanodrop test was performed. This would tell us how many ng of DNA could be found in each µL of our samples. The results have been given below:

  • Tube 1 contained 145.5 ng/µL of DNA.
  • Tube 2 contained 164.1 ng/µL of DNA.
  • Tube 3 contained 153.9 ng/µL of DNA.


The remaining DNA was then placed in a -20°C freezer and stored for later use concluding the days lab work.

Week 2

31 July
2013

Transforming DNA

Today a further 4 constructs arrived (Poly(Arginine-Serine), Poly(Arginine-Glycine), 1PJN1 and 1ETF) so it became possible to continue with the lab work: increasing the amount of viable DNA for these samples much like we had done for the Protamine-1-optimized sample which we had recieved a week earlier. To increase the DNA we would transfer the DNA into Nova-Blue bacteria and culture these allowing the bacteria to replicate our own vector constructs. To isolate the DNA we would then move on to miniprepping the cultures. Firstly however the would need to be transformed into the bacteria. The steps taken to do this are listed below:

  • Before transformation could be started the 4µg of DNA we had recieved would need to be diluted to a 1ng/µL concentration as follows:
    • The first step was to dilute the 4µg of vector in 20µL of MilliQ water. This created a 200ng/µL solution.
    • Of the previously created solution 1µL was pipetted into 199µL of MilliQ water creating a 4000 times dilution (1ng/µL).
  • With this 1ng/µL solution the transformation could commense:
    • Of this 1ng/µL solution 1µL was pipetted into 20µL of NB bacteria. The two dilutions could now be stored in the -20°C freezer.
    • The NB/Vector solution was left on ice for a short while before being heat-shocked in a water-bath of 43.6°C for 30 seconds. (This should have been 42°C but the temperature gauge was thought to be broken at this time.)
    • Now the NB bacteria were returned to ice for 2 minutes.
    • After allowing the bacteria to cool 80µL of SOC solution was added. Hereafter the NB bacteria were not returned to ice. Instead they were placed in a 37°C incubator for 60 minutes.

Plating the bacteria

After incubating the bacteria for a hour they were ready to be plated so that we could create a number of cultures. This was done in the following fashion:

  • The following steps were all performed in the vicinity of a blue flame to increase the sterility.
  • The plate was opened and the entire bacterial solution (approx. 101µL) was pipetted onto an ampicillin agar plate.
  • To ensure even culture growth the solution was spread out over the plate using a sterile spreader.
  • The plate with its bacterial spread was then placed in a 37°C incubator and left there overnight to grow.


1 August
2013

Creating the Cultures

Looking ahead to the cloning we would like to perform later on and using the yields of DNA obtained from the Protamine-1-Optimized sample last week a small calculation was performed to see how much DNA we would need and therefore how many cultures would need to be created. As we were going to attempt to use gel extraction to purify the digestion products of these constructs we would need to culture approximately 20 times more DNA than that we would eventually need for the ligation. Based on the average 150ng/µL DNA yield from the Protamine-1-Optimized construct we determined we would need 12 8mL cultures per construct to obtain the correct amount of DNA. This meant that we would would be creating:

  • 12 cultures of Poly(Arginine-Glycine).
  • 12 cultures of Poly(Arginine-Serine).
  • 12 cultures of 1PJN1.
  • 12 cultures of 1ETF.
  • 9 cultures of Protamine-1-Optimized to bring the total number of cultures up to 12.

Again looking ahead to the cloning we saw that we would also need to increase the amount of pBR322 and pET28a vectors we had. For each of these we would need to create 3 8mL cultures to be able to perform an equimolar ligation. This all brought the total number of cultures we would need to create up to 63. The creating of the cultures was then performed in the following manner:

  • All the following steps were performed in the vicinity of a blue flame to increase the sterility.
  • 63 culture tubes were filled with 8mL of LB medium which had been prepared earlier.
  • 8µL of 1000x Ampicillin antibiotics were then added to 60 of the culture tubes. 8µL of 1000x stock Kanamycin antibiotics were then added to the remaining three culture tubes. This was done as the pET28a vectors were resilient to Kanamycin and not to Ampicillin which all the other constructs were.
  • The culture plates for each of the constructs were then retrieved. Instead of, as we did with the previous Protamine-1-Optimized constructs, pipetting a single culture into each of the culture tubes we now to decided to pick a culture and dissolve it in 15µL of water. From this 15µL solution 5µL could be pipetted into a culture tube. This meant that we would not have to pick 12 cultures from the plate per construct (or 9 for the Protamine-1-Optimized construct) but only 4 (or 3 for the Protamine-1-Optimized construct).
  • For the pET28a culture, an eppendorf tube containing a glycerol stock of pET28a vectors in NB bacteria was retrieved and from the -80°C freezer and once thawed, 5µL was pipetted into each of the 3 culture tubes.
  • For the pBR322 culture we would first have to transform the DNA into NB bacteria in the following fashion:
    • Firstly the pBR322 vector DNA would have to be diluted as follows:
      • Add 450µL of MilliQ water to the DNA to create a 100ng/µL stock solution.
      • Take 1µL of the 100ng/µL stock solution and add it to a further 99µL of MilliQ water creating a 1ng/µL stock solution.
    • Using this 1ng/µL stock solution the transformation could commense.
      • 1µL of the stock solution was added to 20µL of NB bacteria.
      • This solution was left on ice for 5 minutes before being placed in a 42°C water bath, heat shocking the bacteria.
      • The bacterial solution was then placed on ice for a further 2 minutes before 80µL of SOC was added to the solution.
      • Without placing on ice first the solution was then placed in a 37°C incubator for 60 minutes.
    • After 60 minutes in the incubator the 20µL of the solution could be pipetted into each of the three pBR322 culture tubes.
    • 60µL of SOC was subsequently added to the remainder of the bacterial solution so that it could be plated (on an Ampicillin agar plate) and in that way serve as a backup should the culture not grow.
  • Now that all the culture tubes were complete they could be placed in a 37°C incubator overnight to grow.

2 August
2013

Retaining the DNA

As there were 63 culture tubes it was decided to perform the miniprep protocol, used to retain the DNA from the cultures, on the cultures in two separate bulks. The first bulk would see the retention of DNA from the 1ETF, 1PJN1 and Poly(Aginine-Glycine) culture tubes. The second bulk would then deal with the Poly(Arginine-Serine), Protamine-1-Optimized, pBR322 and pET28a cultures. This did mean that the second bulk would have more time (several hours) to grow than the cultures of the first bulk. For both the bulks the same protocol was followed:

  • Before beginning with the miniprep protocol 700µL of culture solution was added to 300µL of 50% Glycerol solution. This was done for one culture from each construct so that should something go wrong we would no longer have to worry about plating the desired constructs.
  • To start the miniprep protocol the culture tubes were spun down in a centrifuge for 10 minutes at 3700rpm causing the bacterial cells with the DNA inside to form pellets isolating it from the growth medium.
  • The supernatant that formed above the pellets was discarded and the pellets themselves were resuspended in 250µL of P1 buffer. The tubes were gently shaken by hand until the entire pellet had resuspended.
  • The suspension was then transferred by means of pipetting into a smaller (1.5mL) eppendorf tube.
  • 250µL of P2 buffer was then added to the eppendorf tube and the solution was inverted by hand until it had turned a clear blue.
  • Within 5 minutes of adding the P2 buffer 350µL of N3 buffer was added to the solution and the eppendorf tube was inverted again until the solution was clear again.
  • Once clear the eppendorf tube was placed in the centrifuge and spun for 10 minutes at 13000rpm seperating the bacterial cells from the DNA which remained suspended in the solution. The bacterial cells formed a pellet in the bottom of the eppendorf tube. (Unfortunately the pellet had not completely formed after 10 minutes so the eppendorf tube was spun for a further minute, again at 13000rpm.)
  • As soon as the centrifuge had stopped and we could see that the pellet had properly formed, the supernatant was poured off into a special QIAcolumn. The pellet could be discarded in the bio-hazard waste.
  • The QIAcolumn was subsequently centrifuged for one minute at 13000rpm, during which the DNA vector bound to the column meaning the flow through could be discarded.
  • 750µL of PE buffer was then added to the QIAcolumn before centrifuging it for another minute at 13000rpm. The flow through was discarded.
  • To ensure that all the PE buffer had passed through the column it was then spun yet again for one minute at a speed of 13000rpm. Yet again the flow through could be discarded.
  • The column itself was then placed above a sealable 1.5mL eppendorf tube so that the DNA could be contained and stored. To obtain the DNA from the column 36µL of MilliQ water was pipetted onto the very centre membrane of the column after which it was spun down for one minute at 13000rpm. The flow through now sat in the 1.5mL eppendorf tube and contained the DNA vectors. (It would appear that for the 1ETf and 1PJN1 cultures 72µL of water was used instead of the desired 36µL meaning we had total volume for these tow samples which was twice as large as for the other cultures.)

Nanodrop Test

To determine how much DNA we had acquired for each of the constructs a nanodrop test could be performed. However before doing so all the DNA from a single construct was combined so that we had an indication of how much DNA we had in total. For the Protamine-1-Optimized sample this combination included the 3 50&mico;L solutions we had obtained previously. The results of this nanodrop test are given below:

  • 432µL of Poly(Arginine-Glycine) with a concentration of 265.1ng/µL.
  • 432µL of Poly(Arginine-Serine) with a concentration of 262.3ng/µL.
  • 474µL of Protamine-1-Optimized with a concentration of 209.3ng/µL.
  • 864µL of 1ETF with a concentration of 225.1ng/µL.
  • 864µL of 1PJN1 with a concentration of 120.5ng/µL.
  • 108µL of pBR322 with a concentration of 108.4ng/µL.
  • 108µL of pET28a with a concentration of 62.1ng/µL.


Week 3

5 August
2013

Digestion

Previously we had increased the amount of DNA we had to our disposal by culturing bacteria with containing our constructs and retaining the multiplied DNA using the miniprep method. Each of the five constructs we had designed and received (Protamine-1-Optimized, 1PJN1, 1ETF, Poly(Arginine-Serine) and Poly(Arginine-Glycine)) had successfully been multiplied along with the two vectors (pET28a and pBR322) in which we wished to insert our constructs. To insert our constructs into the two vectors we would first need to digest all the constructs and the vectors using the correct restriction enzymes and then ligate the insert and the vector. Today was focussed around the digestion.

Construct Digestion

As the our desired inserts for the ligation were in the pUC57-Simple vector we would need to perform digestion on all the vectors and then purify the product thereof to obtain the desired insert. However, due to the relatively large size of the inserts we could not do this using the standard PCR purification kit. This meant that purification would have to be done on basis of gel extraction. For this we would need a larger amount of DNA to start with to ensure a sufficient yield upon completion. It was decided that loading 10µg of DNA onto the gel for each construct would be adequate. Insert would be adequate. However for each construct two inserts would be created so each construct would have to provide 2 * 10µg of DNA for loading onto the gel.

For the digestion the following were added together in a PCR eppendorf tube:

Construct 5µg DNA (µL) CutSmart Buffer (µL) Amount of each Enzyme (µL) MilliQ water (µL)
Protamine-1-Optimized 23.9 5 0.7 20.4
1ETF 22.2 5 0.7 22.1
1PJN1 41.5 5 0.7 2.8
Poly(Arginine-Glycine) 18.9 5 0.7 25.4
Poly(Arginine-Serine) 19.1 5 0.7 25.2

For each of the 5 constructs the solutions in the above table were prepared with the exception of the enzymes a total of four times. This provided us with 20µg of DNA in total per construct spread out equally across 4 seperate PCR tubes. To two of these the 0.7µg of the NheI and 0.7µg of the XhoI restriction enzymes were added. The product of the restriction with these enzymes would cut out just the protein sequence from the construct allowing us to ligate that into the pET28a vector for aerobic expression. To the remaining two eppendorf tubes for each of the constructs 0.7µg of the EcoRI and 0.7µg of the HindIII restriction enzymes were added. This restriction would cut our entire construct from the pUC57-simple vector allowing us to ligate that into the pBR322 vector and test our construct anaerobically.

After adding the enzymes the solutions were quickly mixed and placed in the PCR apparatus.

Vector Digestion

Rather more simple than the construct digestion the vectors too needed to be digested. As we would only require 500µg of DNA as a result of this digestion it was not necessary to use 5µg of DNA so it was decided only 2µg would be used per vector. The following solutions were made:

Vector 2µg DNA (µL) CutSmart Buffer (µL) Amount of each Enzyme (µL) MilliQ water (µL)
pBR322 32.2 5 0.7 12.1
pET28a 18.5 5 0.7 25.8

0.7µL of the NheI and 0.7µL of the XhoI restriction enzymes were added to the pET28a vector solution and 0.7µL of the EcoRI and 0.7µL of the HindIII restriction enzymes were added to the pBR322 vector solution. These solutions were then placed in the same PCR apparatus as the construct solutions and the following PCR protocol was run for both the constructs and the vectors simultaneously:

  • Reaction Step: 37°C for 60 minutes
  • Enzyme Inactivation Step: 80°C for 20 minutes
  • Storage Step: 4°C

PCR Purification for the Constructs

Due to the large size of the insert produced by the digestion of the constructs a gel extraction would be used to select the appropriate sections of the digestion product of the constructs. To isolate the correct segments on the gel the following steps were taken:

  • A 1% electrophoresis gel was created with 10 large lanes (each lane large enough for a 120µL sample).
  • For each of the constructs the two PCR solutions containing the same enzymes were pipetted into a single tube creating a single 100µL solution.
  • To each tube containing a 100µL solution 20µL of 6x stock solution loading dye was added bringing the total volume up to 120µL.
  • Each of these 120µL samples were then brought over into one of the 10 available lanes.
  • The gel was the "run" for 60 minutes with a voltage of 100V.
  • After "running" the gel it was removed from its container and placed on a UV light. Here we were able to discern between the different bands. For each of the digestion results the smaller DNA segment was desired so the lowest band in each lane of the gel was cut from the gel and placed in an eppendorf tube.
  • The 10 eppendorf tubes containing the gel cut-outs were then placed in the -20°C freezer for storage until the real DNA extraction would take place.

PCR Puricfication for the Vectors

For the vectors a simple QIAquick PCR purification kit could be used to purify the digestion product as the cut out was smaller than 100 bases for each of the two vectors. The purification was carried out according to the following protocol:

  • To the PCR product 5 volumes of PB buffer were added (In our case this was 250µL of PB buffer as we had 50µL of PRC product.)
  • This solution was placed in a QIAquick spin column and spun for 60 seconds at 13000 rpm. The flow through could be discarded.
  • Now 750µL of PE buffer could be added to the column before spinning it down once more for 60 seconds at 13000 rpm.
  • Having discarded the flow through the column was spun for a further 60 seconds again at 13000 rpm to remove the last of the PE buffer.
  • The column was then placed into a sealable eppendorf tube before adding 42µL of MilliQ water to the very centre membrane of the spin column and leaving it to stand for one minute.
  • The column was now placed in the centrifuge and spun for 60 seconds at 13000 rpm producing a solution containing the desired DNA.

Nanodrop Results

To test how successful the entire process of restriction had been for the vectors the purification products were analysed using the nanodrop spectrometer. the results are given below:

  • pBR322 had a concentration of 11.6ng/µL.
  • pET28a had a concentration of 7.9ng/µL.

Having eluded both of these samples in just 42µL of water meant that we did not have enough vector DNA for the ligation later on (we were aiming for 500ng). To solve this the entire restriction was performed again for the vectors. This meant remaking the solutions for the digestion and restarting the PCR. As it was late in the day, the solutions were prepared, the enzymes were added and the PCR was started. The PCR machine was set to return to 4°C to store the restriction product overnight and the PCR purification could then be performed the next day along with another nanodrop analysis, hopefully with better results.

6 August
2013

Continuing with the Purification

On August 5th digestion was performed on five of our ordered constructs, and on the two vectors in which we would like to place our constructs. At the end of the day the digestion products of the constructs were still within the gel cut outs which had been stored in a -20°C freezer. The constructs had been purified but the yield had been too low for ligation so the digestion was performed once more. Today then, before moving on to the ligation, the constructs would have to be extracted from the gel and the vectors would also have to be purified.

Vector Purification

The purification of the vectors was performed in the same manner this time round as it was the previous time, following the protocol of the QIAquick PCR purification kit. To prevent falling into repetition this protocol will not be discussed here but can be found in the journal entry for August 5th. The results of this purification however, gotten through a nanodrop measurement are given below:

  • pBR322 had a concentration of 15.3ng/µL.
  • pET28a had a concentration of 10.7ng/µL.

Needing these digested vectors for the ligation later on, we had hoped for a yield of at least 500ng of DNA per vector. Based on these results and an estimated volume of around 38µL this meant that we had achieved our goal for the pBR322 vector. For the pET28 factor however this was not the case. Fortunately we had not discarded the solutions from the previous pET28a digestion meaning that their combined volumes and concentrations would be sufficient for the ligation. From now on pET28a(1) will refer to the pET28a sample digested on August 5th with a concentration of 9.8ng/µL and pET28a(2) will refer to the pet28a sample digested today with a concentration of 10.7ng/µL.

Construct Purification

Our constructs had been run on gels to separate the different products formed during the digestion. The desired bands had been cut out from these gels and had been stored in the -20°C freezer overnight. Now we were ready to perform the gel extraction, retrieving the DNA from these gel cut outs. This was done following the QIAquick gel extraction protocol which is explained here:

  • First all the samples were weighed. A single QIAcolumn can be used for up to 400ng of gel, as all our cut-outs were almost double this they were disected into two almost equal parts and spread over two separate eppendorf tubes. The weight of the gel in each tube was noted.
  • To each tube 3 volumes of QG buffer was added. A volume can be defined as the weight of the gel in mg transferred into µL. SO a gel weighing 400mg would have a volume of 400µL, so 1200µL of QG would be added.
  • The eppendorf tubes containing the gel cut-outs and the QG buffer were placed in an incubator set at 50°C for 10 minutes, whilst vortexing the samples at regular (every 2 minutes) intervals until the gel had completely dissolved.
  • To these tubes 1 volume of isopropanol was added. As the addition of this isopropanol would not fit in a single eppendorf tube the solution in each of the tubes was split equally across two separate eppendorf tubes. To each of these separate eppendorf tubes half a volume of isopropanol was added.
  • One of the two tubes was then brought over into a QIAquick column and placed in the centrifuge where it was spun down for 60 seconds at 13000 rpm. After discarding the flow through the second of the two tubes was then brought over into the QIAquick column and spun down in the same fashion. Once more the flow through was discarded.
  • Now 750µL of PE buffer was added to the column before centrifuging at 13000 rpm for 60 seconds. After discarding the flow through the same amount was added and once more and again centrifuged.
  • Removing the flow through the column was then centrifuged again for 60 seconds at 13000 rpm removing the last of the PE buffer.
  • After bringing the column across into a sealable eppendorf tube 36µL of MilliQ water was pipetted onto the very centre membrane of the column which was then let to stand for 60 seconds. Subsequently the column was spun down at 13000 rpm for 60 seconds. The DNA is now in the flow through.
  • Remembering that we split the gel in half in the very first stage of this protocol, the two solutions containing the same DNA were combined so that a total volume of maximally 72µL of each insert was formed.

Nanodrop Results

To check the concentration of the inserts we had acquired a nanodrop test was performed using the spectrometer. The results are given below. Remember that for each construct, two different digestions were performed, one for ligation into pET28a and one for ligation into pBR322.

Construct pET28a Digest (ng/µL) pBR322 Digest (ng/µL)
Protamine 2.6 9.6
1PJN1 5.0 10.5
1ETF 7.0 11.1
Poly(Arginine-Glycine) 11.8 16.0
Poly(Arginine-Serine) 8.3 13.4

Ligation

Each of our five constructs (Protamine-1-Optimized, 1PJN1, 1ETF, Poly(Arginine-Glycine) and Poly(Arginine-Serine)) restriction was performed in two ways. The first cutting at the NheI and XhoI restriction sites allowing us to place just the protein sequence into the pET28a vector. The second restriction cut at the EcoRI and HindIII sites, thus allowing us to ligate the entire construct (protein sequence along with promoters, terminators and His-tags) into the pBR322 vector.

Before being able to prepare the ligation solution it was necessary to perform a number of calculations. For each vector we added to the solution we wished to add five times as many inserts. This would ensure that our inserts would be ligated into the vectors. To start with we calculated how many µL of our digested vectors would need to be added to the ligation solution to obtain 100ng of vector DNA.

Vector Concentration (ng/µL) 100g DNA (µL) Number of Bases in Vector
pBR322 15.3 6.6 4330
pET28a(1) 9.8 10.2 5296
pET28a(2) 10.7 9.4 5296

By dividing 100ng by the number of bases in a single vector and multiplying that number by the number of bases in a single insert it can be determined how many ng of the insert is needed for molar equality (having an equal amount of vectors as there are inserts).

By then dividing the amount of DNA needed for molar equality (in ng) by the concentration of each insert the volume (in µL) of insert solution needed would be given. As we did not want molar equality but five times as many inserts as there are vectors this volume could be multiplied by five.

The calculations for the pBR322 inserts are given here:

Construct Number of Bases Concentration (ng/µL) ng Needed for Molar Equality (ng) Volume Needed for Molar Equality (µL) Volume Needed for 5x Molar Equality (µL)
Protamine-1-Optimized 489 9.2 11.3 1.23 6.2
1PJN1 726 10.5 16.8 1.6 8.0
1ETF 756 11.1 17.5 1.58 7.9
Poly(Arginine-Glycine) 771 16.0 17.8 1.11 5.6
Poly(Arginine-Serine) 771 13.4 17.8 1.32 6.6

For the pET28a vector neither of the two digested samples had enough DNA to provide 100ng for ligation with each of the five constructs. Therefore it was decided to use the pET28a(1) digestion product for the Poly(Arginine-Glycine) and Poly(Arginine-Serine) inserts. The pET28a(2) digestion product would then be used for the remaining three ligations (with Protmaine-1-Optimized, 1PJN1 and 1ETF).

The calculations are given here for the pET28a(1) ligation:

Construct Number of Bases Concentration (ng/µL) ng Needed for Molar Equality (ng) Volume Needed for Molar Equality (µL) Volume Needed for 5x Molar Equality (µL)
Poly(Arginine-Glycine) 447 11.8 8.44 0.72 3.6
Poly(Arginine-Serine) 447 8.3 8.44 1.02 5.1

And for the pET28a(2) ligation here:

Construct Number of Bases Concentration (ng/µL) ng Needed for Molar Equality (ng) Volume Needed for Molar Equality (µL) Volume Needed for 5x Molar Equality (µL)
Protamine-1-Optimized 165 2.6 3.11 1.2 6.0
1PJN1 402 5.0 7.6 1.52 7.6
1ETF 432 7.0 8.2 1.2 5.9

Having determined the volumes of insert and vector we would need for the ligation reactions, the ligation solutions could be prepared. In addition to the vectors and inserts we would also need to add a buffer, MilliQ water and Ligase. All reaction solutions would end up equal to 20µL. The table below shows the amounts used to prepare the pBR322 vector ligation samples:

Construct Amount of Vector pBR322 (µL) Amount of Insert (µL) 10x Buffer (µL) MilliQ Water (µL) Ligase (µL)
Protamine-1-Optimized 6.6 6.2 2 4.2 1
1PJN1 6.6 8.0 2 2.4 1
1ETF 6.6 7.9 2 2.5 1
Poly(Arginine-Glycine) 6.6 5.6 2 4.8 1
Poly(Arginine-Serine) 6.6 6.6 2 3.8 1

Below are give the solution quantities for the pET28a(1) and pET28a(2) vector ligations respectivly:

Construct Amount of Vector pET28a(1) (µL) Amount of Insert (µL) 10x Buffer (µL) MilliQ Water (µL) Ligase (µL)
Poly(Arginine-Glycine) 10.2 3.6 2 3.1 1
Poly(Arginine-Serine) 10.2 5.1 2 1.7 1
Construct Amount of Vector pET28a(2) (µL) Amount of Insert (µL) 10x Buffer (µL) MilliQ Water (µL) Ligase (µL)
Protamine-1-Optimized 9.4 6.0 2 1.6 1
1PJN1 9.4 7.6 2 0.0 1
1ETF 9.4 5.9 2 1.7 1

Having prepared the above solutions, and having added the Ligase only at the very last moment, the solutions were placed in the PCR apparatus ready for the ligation. The ligation protocol was set as follows:

  • 37°C for 120 minutes for the ligation reaction.
  • 65°C for 10 minutes for the Ligase inactivation.
  • 4°C FOREVER to store the ligation products until they would be used again.

The samples were left in the PCR apparatus overnight.

Preparing Agar Plates

Before leaving, and in anticipation of the coming steps we decided to prepare a number of Ampicillin agar plates. The agar solution itself was made by mixing the following:

  • 5g Peptones
  • 5g NaCl
  • 2.5g Yeast Extract
  • 7.5g Agar
  • 500mL Demineralised Water

By placing the above solution in the autoclave the agar was produced. Once cool 500µL of Ampicillin was added to the solution whilst being stirred. In the vicinity of a blue bundsen flame 25 Ampicilling agar plates were poured which were then left to harden before being placed in the 4°C refrigerator.

7 August
2013

Transformation

Having left the ligation products in the PCR apparatus at 4°C overnight we were now able to transform these into NoveBlue bacteria ready to plate them. This plating will allow us to perform a ColonyPCR later on to check the efficiency of our ligation. It would also allow us to replicate, duplicate and sequence correctly ligated vectors and inserts. For the transformation we transformed all 10 ligation products (each of the five constructs in both the vectors) using the same transformation protocol:

  • All steps were performed in the vicinity of a blue flame to increase sterility.
  • 1µL of each ligation product was pipetted into 20µL of NovaBlue bacteria.
  • These were left to stand on ice for 5 minutes.
  • Then to heat shock the samples they were placed in a water bath at 42°C for 30 seconds.
  • The samples were subsequently returned to ice for 2 minutes.
  • Then 80µL of SOC solution was added to each of the samples. After this they would not be allowed to return to ice.
  • The samples were then placed in an incubator set to 37°C for 60 minutes.

Apart from transforming the ligation products three controls were also prepared. This was done to check that the restriction of the vectors had been successful. To make the control samples made samples of 20µL consisting of the same amount of vector as used in the ligation solutions. The remaining volume (up to 20µL) was then filled with water. The transformation protocol of these controls follows that which was used for the ligation products.


Plating

Once the transformations had been incubated for an hour they were ready for plating to allow colonies to grow on the plates. The samples which had been ligated into the pET28a vectors and the two pET28a vector controls were plated onto agar platescontianing Kanamycin antibiotics. The samples which had been ligated into pBR322 vectors and the pBR322 vector control were plated onto agar plates containing Ampicillin antibiotics. For the plating the following protocol was used:

  • In the vicinity of a blue bunsen flame the entire sample (101µL) was pipetted onto the centre of the agar plate.
  • A spreader which had been stored in 100% Ethanol was lit in the flame burning off the Ethanol and sterilizing the spreader.
  • The sterile spreader was allowed to cool before being placed onto the agar plate and spreading out the bacterial sample equally.

The plates had now been spread with the transformations of the ligation products and were placed in the 37°C incubator overnight. Here they could grow and with luck, be used for ColonyPCR the next day.


8 August
2013

Colony Picking and PCR

Having plated NovaBlue bacteria containing our own ligated vectors (Each of our five constructs: Protamine-1-Optimized, 1PJN1, 1ETF, Poly(Arginine-Glycine) and Poly(Arginine-Serine), were ligated into both pBR322 and pET28a vectors) we could now pick a number of these samples, check the ligation products using PCR and culture those ligation products which had been successful. Due to the late delivery of the pBR322 primers it was decided to perform the colony PCR on just the pET28a ligations. The pBR322 agar plates would be stored at 4°C until the primers arrived. The following protocol was then used to perform the colony picking and PCR:

  • All steps up to the PCR itself were performed in the vicinity of a blue bunsen flame for increased sterility.
  • From each agar plate (each plate containing one of the constructs ligated with the pET28a vector) 5 seperate colonies were picked and dissolved in 15µL of sterile water. We had also plated the two separately digested pET28a factors as controls and from these plates a single colony was also picked and dissolved in 15µL of sterile water. Photos of these plates are visible below:

TU-Eindhoven Images pET28a Protamine.jpg
pET28a_Protamine pEt28a-Protamine
TU-Eindhoven Images pET28a 1PJN1.jpg
pET28a_1PJN1 pET28a-1PJN1
TU-Eindhoven Images pET28a 1ETF.jpg
pET28a_1ETF pET28a-1ETF
TU-Eindhoven Images pET28a P(RG) 2.jpg
pET28a_P(RG) pET28a-Poly(Arginine-Glycine)
TU-Eindhoven Images pET28a P(RS).jpg
pET28a_P(RS) pET28a-Poly(Arginine-Serine)
TU-Eindhoven Images pET28a 1 Control.jpg
pET28a_1_Control pET28a(1) Control
TU-Eindhoven Images pET28a 2 Control.jpg
pET28a_2_Control pET28a(2) Control

  • After dissolving the pickings they were ready for PCR. Before starting the PCR protocol the following solutions had to be made:
    • 9µL of sterile water.
    • 1.25µL of 10µM T7 Fwd Primer.
    • 1.25µL of 10µM T7 Rw Primer.
    • 12.5µL of Kappa2G 2x solution.
    • 1µL of the picking solution.
  • Having mixed the above, adding the Kappa2G last, the PCR tubes were placed in the PCR and run with the following protocol:
    • Initial Denaturation: 95°C for 3 minutes.
    • The following steps should be performed in this order, repeating the process a total of 34 times.
      • Denaturation: 95°C for 15 seconds.
      • Annealing: 58°C for 15 seconds.
      • Extension: 72°C for 20 seconds.
    • Final Extension: 72°C for 10 minutes.
    • Storage: 4°C FOREVER.
  • Having completed the PCR protocol 4µL of 6x Loading Dye was added to each of the PCR solutions. Subsequently 18µL of each was loaded onto a 1.5% agarose electrophoresis gel which was prepared by mixing the following:
    • 1.8g of Agarose.
    • 120mL of 1x TAE buffer
    • 12µL of CyberSafe.
  • The gel was then run at 100V for 75 minutes before placing the gel into a UV spectrometer. Here we could analyse the gel and decide which of the ligation products were successful. Of each of the five constructs two successfully ligated bacteria colonies were selected and these would then be grown in a larger culture. The gel result is shown below.

TU-Eindhoven Images PCR Colony Gel pET28a Construct 1 to 5.png
pET28a_Protamine PCR Colony Gel for pET28a ligated constructs. Columns from left to right: 1 - 1Kb ladder, 2 - 0.1Kb ladder, 3-7 - Protamine-1-Optimized Sequences, 8-12 - 1PJN1 Sequences, 13-17 - 1ETF Sequences, 18-22 - Poly(Arginine-Glycine) Sequences, 23-27 - Poly(Arginine-Serine) Sequences, 28 - pET28a (1) Control, 29 - pET28a (2) Control, 30 - 0.1Kb ladder.

Culturing the Ligation Products

Having analyzed the gel and having chosen two successful ligations for each of the constructs these were then cultured. This was done in the following manner:

  • All below steps were performed near a blue bunsen flame to increase sterility.
  • Culture tubes were filled with 8mL of LB medium.
  • To each of the culture tubes 8µL of Kanamycin was added.
  • 5µL of the picked colony solution was pipetted into the culture medium.
  • The culture tubes were then placed in the 37°C incubator overnight.

9 August
2013

Miniprep

On August 8th a number of constructs were chosen to be cultured, multiplying the number of correctly ligated DNA vectors we had available to ourselves. To retain this DNA the miniprep protocol would be performed on each of the cultures:

  • To start the miniprep protocol the culture tubes were spun down in a centrifuge for 10 minutes at 3700rpm causing the bacterial cells with the DNA inside to form pellets isolating it from the growth medium.
  • The supernatant that formed above the pellets was discarded and the pellets themselves were resuspended in 250µL of P1 buffer. The tubes were gently shaken by hand until the entire pellet had resuspended.
  • The suspension was then transferred by means of pipetting into a smaller (1.5mL) eppendorf tube.
  • 250µL of P2 buffer was then added to the eppendorf tube and the solution was inverted by hand until it had turned a clear blue.
  • Within 5 minutes of adding the P2 buffer 350µL of N3 buffer was added to the solution and the eppendorf tube was inverted again until the solution was clear again.
  • Once clear the eppendorf tube was placed in the centrifuge and spun for 10 minutes at 13000rpm seperating the bacterial cells from the DNA which remained suspended in the solution. The bacterial cells formed a pellet in the bottom of the eppendorf tube. (Unfortunately the pellet had not completely formed after 10 minutes so the eppendorf tube was spun for a further minute, again at 13000rpm.)
  • As soon as the centrifuge had stopped and we could see that the pellet had properly formed, the supernatant was poured off into a special QIAcolumn. The pellet could be discarded in the bio-hazard waste.
  • The QIAcolumn was subsequently centrifuged for one minute at 13000rpm, during which the DNA vector bound to the column meaning the flow through could be discarded.
  • 750µL of PE buffer was then added to the QIAcolumn before centrifuging it for another minute at 13000rpm. The flow through was discarded.
  • To ensure that all the PE buffer had passed through the column it was then spun yet again for one minute at a speed of 13000rpm. Yet again the flow through could be discarded.
  • The column itself was then placed above a sealable 1.5mL eppendorf tube so that the DNA could be contained and stored. To obtain the DNA from the column 42µL of MilliQ water was pipetted onto the very centre membrane of the column after which it was spun down for one minute at 13000 rpm. The flow through now sat in the 1.5mL eppendorf tube and contained the DNA vectors.

Nanodrop Results

A useful step now, having acquired our ligated DNA vectors would be to send them off for sequencing to confirm that we had indeed ligated and cultured the correct vectors and inserts. Before being able to do this, we would need to determine the concentrations of each of the miniprep products.

Vector Colony Picking Number Concentration (ng/µL)
Protamine-1-Optimized 1 60.0
Protamine-1-Optimized 2 65.9
1PJN1 3 72.1
1PJN1 4 66.6
1ETF 3 64.1
1ETF 4 72.8
Poly(Arginine-Glycine) 3 73.5
Poly(Arginine-Glycine) 5 117.8
Poly(Arginine-Serine) 2 206.7
Poly(Arginine-Serine) 5 57.8

Vector Sequencing

To sequence each of the vectors we sent off samples of our DNA to an external sequencing company. For this company to fully sequence each of our vectors we had to create two solutions for each vector we wished to sequence, one with the T7 FWD primer and one with the T7 RW primer, both with a concentration of 10µM. The second requirement was that we added between 400ng and 600ng of our DNA vectors. Unfortunately the maximal volume of the entire solution was 7µL, so for constructs with a concentration lower than 67ng/µL the minimal amount of DNA desired for sequencing was not reached. This led to the creation of the following solutions, with the same solution being made for both primers:

Vector Colony Picking Number Volume Vector Solution (µL) Water (µL) Primer (µL)
Protamine-1-Optimized 1 6.0 0.0 1.0
Protamine-1-Optimized 2 6.0 0.0 1.0
1PJN1 3 6.0 0.0 1.0
1PJN1 4 6.0 0.0 1.0
1ETF 3 6.0 0.0 1.0
1ETF 4 6.0 0.0 1.0
Poly(Arginine-Glycine) 2 6.0 0.0 1.0
Poly(Arginine-Glycine) 5 4.0 2.0 1.0
Poly(Arginine-Serine) 3 3.0 3.0 1.0
Poly(Arginine-Serine) 5 6.0 0.0 1.0

Having prepared these solutions in small PCR eppendorf tubes they were packaged and sent off for sequencing.

Colony Picking and PCR

On August 8th we had performed the colony picking and PCR for the constructs which had been ligated into the pET28a vector. As we did not have the primers for the pBR322 vector those colony plates were stored at 4°C. Today however the pBR322 primers had arrived and we could perform the colony pickings for the ligated pBR322 vectors. It should be noted that the primers we used for the pBR322 vector had been designed ourselves with the following sequences:

pBR322 FWD Primer 5’- CCC GAA AAG TGC CAC CTG -3’
pBR322 RW Primer 5’- GT GCC GAG GAT GAC GATG -3’

To then perform the colony PCR the following solutions had to be created:

  • Much like for the pET28a ligated vectors we picked five colonies for each of the five constructs ligated into the pBR322 vector. These pickings were dissolved in 5µL of sterile water. Along with the five pickings per construct we also picked one colony from the control plate, which contained just the pBR322 vector. Photos of the agar plates are shown below:

TU-Eindhoven Images pBR322 Protamine.jpg
pBR322_Protamine pBR322-Protamine
TU-Eindhoven Images pBR322 1PJN1.jpg
pBR322_1PJN1 pBR322-1PJN1
TU-Eindhoven Images pBR322 1ETF.jpg
pBR322_1ETF pBR322-1ETF
TU-Eindhoven Images pBR322 P(RG).jpg
pBR322_P(RG) pBR322-Poly(Arginine-Glycine)
TU-Eindhoven Images pBR322 P(RS).jpg
pBR322_P(RS) pBR322-Poly(Arginine-Serine)
TU-Eindhoven Images pBR322 Control.jpg
pBR322_Control pBR322 Control


  • We could now go ahead and prepare our PCR solutions by mixing the following:
  • 9µL of sterile water.
  • 1.25µL of the FWD primer.
  • 1.25µL of the RW Primer.
  • 1µL of the pBR322 ligated vector colony picking solution.
  • 12.5µL of Kapa2G.
    • We made sure to only add the Kapa2G at the very end just before placing the solutions in the PCR.

Having made the above solutions they were brought across to the PCR apparatus which then performed the following PCR protocol:

  • Initial Denaturation: 95°C for 3 minutes.
  • The following steps should be performed in this order, repeating the process a total of 34 times.
    • Denaturation: 95°C for 15 seconds.
    • Annealing: 58°C for 15 seconds.
    • Extension: 72°C for 20 seconds.
  • Final Extension: 72°C for 10 minutes.
  • Storage: 4°C FOREVER.

Having completed the PCR protocol 4µL of 6x Loading Dye was added to each of the PCR solutions. Subsequently 18µL of each was loaded onto a 1.5% agarose electrophoresis gel which was prepared by mixing the following:

  • 1.8g of Agarose.
  • 120mL of 1x TAE buffer
  • 12µL of CyberSafe.

The gel was then run at 100V for 75 minutes before placing the gel into a UV spectrometer. Here we could analyse the gel and decide which of the ligation products were successful. As it was a Friday afternoon there was no possibility to culture the correctly ligated vectors so these were stored in the 4°C refrigerator and left there until they could be cultured.

Week 4

12 August
2013

Transforming and Plating New Constructs

Today we began work on four new constructs which had arrived late last week. The constructs that we had received were: EGFP, 1G70, Poly(Threonine-Lysine) and Poly(Lysine-Serine). For more information of these constructs please see the wetlab preparation page. The first step to be performed on each of the constructs was the preparing of two dilations. The first a 200ng/µL dilation made by adding 20µL of MilliQ water to the standard 4µg of DNA we recieved for each construct. From this dilution we then took 1µL and added it to another 199µL of MilliQ water forming a 1ng/µL solution which we could use for the transformation:

  • All steps for the transformation were performed near a blue flame for sterility.
  • Start by adding 1µL of the 1ng/µL solution to 20µL of NB bacteria.
  • Place the bacteria on ice and let them stand for 5 minutes.
  • Heat shock the bacteria by placing them in a water bath of 42°C for 30 seconds before returning them to ice for two minutes.
  • Now add 80µL of SOC to each sample and place the samples in a 37°C incubator for an hour. The samples should not (and were not) returned to ice.

This concludes the transformation stage of the constructs which are now enclosed within the NB bacteria. After incubation the bacteria can therefore be plated onto Ampicillin agar plates.

  • In the vicinity of a blue bunsen flame place pipet the entire solution of bacterial cells and SOC onto the centre of the plate.
  • Using a sterile spreader spread out the solution over the gel surface.
  • The plates can now be incubated at 37°C for an overnight growth.

This concludes the work on the new constructs for today.

Transforming and Plating Old Constructs

Last week a number of constructs were digested and ligated into pET28a. These new vectors were then multiplied and retained by performing a culture and miniprep respectively. These new vectors could now be transformed into BL21 bacteria so that expression could be induced using IPTG. Before embarking on the transformation however the following solutions had to be made. As you can see we no longer use all 10 ligated constructs to reduce the work load and will continue with one of each. The concentrations used were determined last week. These solutions will create 1ng/µL solutions of each of the ligated vector solutions.

Vector Colony Picking Number Concentration (ng/µL) Sterile Water (µL) Vector Solution (µL)
Protamine-1-Optimized 1 60.0 59.0 1.0
1PJN1 3 72.1 71.1 1.0
1ETF 4 72.8 71.8 1.0
Poly(Arginine-Glycine) 3 73.5 72.5 1.0
Poly(Arginine-Serine) 5 57.8 56.8 1.0

Having prepared the above solutions the transformation could be started:

  • All steps for the transformation were performed near a blue flame for sterility.
  • Start by adding 1µL of the 1ng/µL solution to 20µL of BL21 bacteria.
  • Place the bacteria on ice and let them stand for 5 minutes.
  • Heat shock the bacteria by placing them in a water bath of 42°C for 30 seconds before returning them to ice for two minutes.
  • Now add 80µL of SOC to each sample and place the samples in a 37°C incubator for an hour. The samples should not (and were not) returned to ice.

This concludes the transformation stage of the constructs which are now enclosed within the BL21 bacteria. After incubation the bacteria can therefore be plated onto Kanamycin agar plates.

  • In the vicinity of a blue bunsen flame place pipet the entire solution of bacterial cells and SOC onto the centre of the plate.
  • Using a sterile spreader spread out the solution over the gel surface.
  • The plates can now be incubated at 37°C for an overnight growth.

This concludes the work on the ligated pET28a constructs for today.

Creating Small Cultures

As we were unable to produce small cultures of the old constructs ligated into the pBR322 vector last week this too would be performed today. Before beginning a new batch of LB medium was prepared:

  • The LB medium was created by mixing the following:
    • 10g Peptones
    • 10g NaCl
    • 5g Yeast Extract
    • 1L Demineralised Water
  • After adding together the above, the solution was autoclaved and left to cool.

One the LB medium was ready for use the culture preparation could be performed:

  • Using the electrophoresis gel from the previous week two ligated vectors were chosen to cultured for each of the five constructs.
  • This meant that 10 culture tubes would have to be filled with 8mL of LB medium each.
  • To each tube a further 8µL of Ampicillin was added.
  • Finally 8µL of the chosen construct was added and the culture tubes were placed in the 37°C incubator for overnight growth.

This concluded not only the work on the pBR322 ligated constructs for today, but also the rest of the days work.

13 August
2013

Miniprepping ligated pBR322 vector cultures

On August 12th the pBR322 ligated constructs were placed in an incubator for overnight culture growth. Today we removed these cultured samples from the incubator, ready to retain the DNA. To do this the miniprep protocol would be used for each of the culture tubes. As a reminder, we had 10 culture tubes, 2 for each of the ligation constructs: Protamine-1-Optimized, 1PJN1, 1ETF, Poly(Arginine-Glycine), Poly(Arginine-Serine) ligated with pBR322. The miniprep went as follows:

  • First the culture tubes were spun down in a centrifuge for 10 minutes at 3700G causing the bacterial cells with the DNA inside to form pellets isolating it from the growth medium.
  • The supernatant that had formed above the pellets was discarded and the pellets themselves were resuspended in 250µL of P1 buffer. The tubes were gently shaken by hand until the entire pellet had resuspended.
  • The suspension was then transferred by means of pipetting into a smaller (1.5mL) eppendorf tube.
  • 250µL of P2 buffer was then added to the eppendorf tube and the solution was inverted by hand until it had turned a clear blue.
  • Within 5 minutes of adding the P2 buffer 350µL of N3 buffer was added to the solution and the eppendorf tube was inverted again until the solution was clear again.
  • Once clear the eppendorf tube was placed in the centrifuge and spun for 10 minutes at 13000rpm seperating the bacterial cells from the DNA which remained suspended in the solution. The bacterial cells formed a pellet in the bottom of the eppendorf tube. (Unfortunately the pellet had not completely formed after 10 minutes so the eppendorf tube was spun for a further minute, again at 13000rpm.)
  • As soon as the centrifuge had stopped and we could see that the pellet had properly formed, the supernatant was poured off into a special QIAcolumn. The pellet could be discarded in the bio-hazard waste.
  • The QIAcolumn was subsequently centrifuged for one minute at 13000rpm, during which the DNA vector bound to the column meaning the flow through could be discarded.
  • 750µL of PE buffer was then added to the QIAcolumn before centrifuging it for another minute at 13000rpm. The flow through was discarded.
  • To ensure that all the PE buffer had passed through the column it was then spun yet again for one minute at a speed of 13000rpm. Yet again the flow through could be discarded.
  • The column itself was then placed above a sealable 1.5mL eppendorf tube so that the DNA could be contained and stored. To obtain the DNA from the column 42µL of MilliQ water was pipetted onto the very center membrane of the column after which it was spun down for one minute at 13000rpm. The flow through now sat in the 1.5mL eppendorf tube and contained the DNA vectors.

The following concentrations were then measured for each of the DNA samples:

Vector Colony Picking Number Concentration (ng/µL)
Protamine-1-Optimized 1 93.9
Protamine-1-Optimized 2 144.8
1PJN1 1 90.5
1PJN1 2 122.4
1ETF 3 86.4
1ETF 4 66.9
Poly(Arginine-Glycine) 1 71.4
Poly(Arginine-Glycine) 2 71.6
Poly(Arginine-Serine) 1 61.2
Poly(Arginine-Serine) 5 75.8

We later saw that the elution for the Protamin-1-Optimized, picking 2, solution had not been successful as the volume of retained DNA was a mere 10µL. This meant that from now on only one of the Protamine samples would be available.

Sequencing

Having retained the DNA vectors we could send off samples for sequencing. Like the previous time, for each of the samples 2 sequencing solutions would have to be prepared. One would contain 1µL of our self-designed pBR322 FWD primer and the other would contain1µL of our self-designed pBR322 RW primer. The following solutions were therefore made:

Vector Colony Picking Number Volume Vector Solution (µL) Water (µL) Primer (µL)
Protamine-1-Optimized 1 6.0 0.0 1.0
Protamine-1-Optimized 2 4.0 2.0 1.0
1PJN1 1 6.0 0.0 1.0
1PJN1 2 5.0 1.0 1.0
1ETF 3 6.0 0.0 1.0
1ETF 4 6.0 0.0 1.0
Poly(Arginine-Glycine) 1 6.0 0.0 1.0
Poly(Arginine-Glycine) 2 6.0 0.0 1.0
Poly(Arginine-Serine) 1 6.0 0.0 1.0
Poly(Arginine-Serine) 5 6.0 0.0 1.0

As mentioned there was only a small elution volume for the Protamine-1-Optimized, picking 2, DNA solution, so we could only prepare the FWD sequencing sample. For the reverse solution the DNA quantity was too low.

As we would only be needing the pBR322 constructs for anaerobic expression, which would only come after we had tested the CEST contrast of each construct, these DNA vectors were placed in the -20°C freezer and were to be left there until needed again in a later stage of this project.

Culturing New Constructs

On August 12th work began on four new constructs which had arrived: EGFP, 1G70, Poly(Threonine-Lysine) and Poly(Lysine-Serine). We had transformed each of the constructs into NovaBlue bacteria and had left these to grow overnight on Ampicillin agar plates. Today we would pick a number of grown colonies and culture them in small cultures. To do this the following steps were taken:

  • All the following steps were performed near a blue flame for increased sterility.
  • Fill 16 cultures tubes with 8mL of LB medium.
  • Add 8µL of Ampicillin to each of the culture tubes.
  • From each of the four culture plates 2 colonies were picked and dissolved in 15µL of sterile water.
  • 7.5µL of this bacterial picking solution was then pipetted into one of the culture tubes, until all tubes contained a portion of bacteria. Great care was taken in the labelling of the cultures so we could trace back which picking had been inserted into which tube.
  • The culture tubes were then placed in the 37°C incubator and left for overnight growth.

It should be noted that four culture tubes were created per sample to ensure a large enough DNA amplification to be able to perform a restriction, gel extraction and ligation later on. Previously we had made 12 of these cultures per construct but it turned out that that was far too much (a miscalculation on our part), therefore we chose to create only four 8mL cultures per construct.

Culturing Old Constructs

Apart from just transforming and plating the new constructs mentioned above, we had also transformed and plated the older pET28a ligated constructs on August 12th. These too had been left to grow overnight and we were now ready to continue work on these samples. As we wished to move onto the expression of our proteins we first wished to perform some tests to see how best to perform the expression (which environment we would need). Therefore it was decided that of the five constructs we had ligated with the pET28a factor and transformed into BL21 before plating, only two would be cultured further for the time being. Looking ahead we knew that we would like to perform expression on August 13th which meant growing the bacteria today, and adding IPTG tomorrow when the Optical Density (from now on: OD) was satisfactory. It was decided that a 100mL culture would be best suited to our desires as we would then be able to perform a large number of tests on the medium. The steps then for growing the bacteria in this 100mL culture was as follows:

  • Firstly two 100mL culture mediums were created by mixing the following in two small Erlenmeyer flask:
    • 1g Peptones
    • 1g NaCl
    • 0.5g Yeast Extract
    • 100mL Sterile Water
  • The above mentioned solutions were then placed in the autoclave to be sterilised.
  • After having cooled down 100µL of Kanamycin antibiotics were added to each of the flasks.
  • Subsequently a single colony was picked from each of the following agar plates: Protamine-1-Optimized-pET28a and Poly(Arginine-Glycine)-pET28a. The two colonies were then transferred to one of the two flasks by ejecting the pipet point into the medium.
  • The culture flasks were then placed in the 37°C incubator and left there to grow overnight.

14 August
2013

Miniprepping New Constructs

On August 13th the four newest constructs (EGFP, 1G70, Poly(Threonine-Lysine) and Poly(Lysine-Serine)) were being cultured and were therefore placen in a 37°C incubator overnight. It was now time to retain the increased DNA using the miniprep protocol:

  • First the culture tubes were spun down in a centrifuge for 10 minutes at 3700G causing the bacterial cells with the DNA inside to form pellets isolating it from the growth medium.
  • The supernatant that had formed above the pellets was discarded and the pellets themselves were resuspended in 250µL of P1 buffer. The tubes were gently shaken by hand until the entire pellet had resuspended.
  • The suspension was then transferred by means of pipetting into a smaller (1.5mL) eppendorf tube.
  • 250µL of P2 buffer was then added to the eppendorf tube and the solution was inverted by hand until it had turned a clear blue.
  • Within 5 minutes of adding the P2 buffer 350µL of N3 buffer was added to the solution and the eppendorf tube was inverted again until the solution was clear again.
  • Once clear the eppendorf tube was placed in the centrifuge and spun for 10 minutes at 13000rpm seperating the bacterial cells from the DNA which remained suspended in the solution. The bacterial cells formed a pellet in the bottom of the eppendorf tube. (Unfortunately the pellet had not completely formed after 10 minutes so the eppendorf tube was spun for a further minute, again at 13000rpm.)
  • As soon as the centrifuge had stopped and we could see that the pellet had properly formed, the supernatant was poured off into a special QIAcolumn. The pellet could be discarded in the bio-hazard waste.
  • The QIAcolumn was subsequently centrifuged for one minute at 13000rpm, during which the DNA vector bound to the column meaning the flow through could be discarded.
  • 750µL of PE buffer was then added to the QIAcolumn before centrifuging it for another minute at 13000rpm. The flow through was discarded.
  • To ensure that all the PE buffer had passed through the column it was then spun yet again for one minute at a speed of 13000rpm. Yet again the flow through could be discarded.
  • The column itself was then placed above a sealable 1.5mL eppendorf tube so that the DNA could be contained and stored. To obtain the DNA from the column 42µL of MilliQ water was pipetted onto the very center membrane of the column after which it was spun down for one minute at 13000rpm. The flow through now sat in the 1.5mL eppendorf tube and contained the DNA vectors.

The following concentrations were then measured for each of the DNA samples:

Vector Concentration (ng/µL)
EGFP 208.9
1G70 165.6
Poly(Threonine-Lysine) 139.7
Poly(Lysine-Serine) 136.5

Digestion

As we did for the previous batch of constructs we would now digest these newest constructs. After digestion we would then, as we did previously for the older constructs have to perform gel extraction to purify the digestion products of these constructs. This would mean digesting a total of 20µg of each construct. This would provide us with 10µg to digest for ligation into the pET28a vector and 10µg of to digest for ligation into the pBR322 vector. For the former digestion the XhoI and NheI restriction enzymes would be used. For the latter digestion we would use the EcoRI and HindIII restriction enxymes, to later allow us to ligate the restriction product into the pBR322 vector. As digestion is not optimal when 10µ of DNA are digested in a single solution each construct would be digested in four separate solutions each containing 5µg. Two of these solutions would contain the enzymes for ligation into the pET28a vector and the remaining 2 solutions the enzymes for ligation in pBR322. The Complete solution for the digestions are given below:

Construct Concentration (ng/µL) Volume for 5µg of DNA (µL) Cutsmart Buffer (µL) Enzyme (µL) Sterile Water (µL)
EGFP 208.9 23.9 5.0 0.7 19.7
1G70 165.6 30.2 5.0 0.7 13.4
Poly(Threonine-Lysine) 139.7 35.8 5.0 0.7 7.8
Poly(Lysine-Serine) 136.5 36.6 5.0 0.7 7.0

As mentioned two restriction enzymes were added to each solution. The given Enzyme volume is the amount that should be added of each of the two enzymes. It should also be noted that for the Poly(Threonine-Lysine) and Poly(Lysine-Serine) there was a slight deficit in the amount of DNA available for one of the solutions. This meant that one solution did not contain 5µg of DNA but slightly less (approx. 4.5µg).

We also had to digest some more of both the vectors. For each vector we aimed to digest a total of 2µg. Therefore the following solutions were made:

Vector Volume for 5µg of DNA (µL) Cutsmart Buffer (µL) Enzyme (µL) Sterile Water (µL)
pET28a 18.5 5.0 0.7 25.8
pBR322 32.2 5.0 0.7 12.1

Here we used the vector DNA that was prepared in the earlier stages (see August 2nd).

These solutions (Both for the vectors as well as the constructs were then placed in the PCR apparatus and set witht he following time schedule:

  • Reaction step: 1 hour at 37°C
  • Enzyme inactivation step: 20 minutes at 80°C
  • Storage step: Forever at 4°C

The restriction products were then run and left at 4°C until they were needed again the next day.

Testing the Expression

On August 13th 2 cell cultures had been placed in the 37°C incubator to grow the bacteria overnight. It was now time to induce the expression. This would be done aerobically for the time being. It is important to test the protein expression on a small scale to start with so that you reduce risks when scaling up. It was decided that once we had induced expression by addition of IPTG that we would take samples of the expression medium every hour to get a good view of the expression curve. These samples would be collected today and analysed tomorrow. The following procedure was followed in order to obtain our samples:

  • An Optical density measurement of the cell culture was taken to check the cell growth. An optical density above 0.6 would mean that expression induction would be possible. The following optical densities were found:
    • Protamine culture: 2.140
    • Poly(Arginine-Glycine) culture: 2.287
  • For this reason 50µL of IPTG was added to each of the cultures. After having placed each culture in the incubator for a further 15 minutes it occurred to us that an optical density above 2 might be far to high for proper expression as the medium would not contain large enough food supplies. The following emergency procedure was then performed with haste:
    • First three test sample tubes were made each with a different amount of new LB medium and a small amount of our existing cell culture:
      • 11mL LB and 1mL cell culture
      • 10mL LB and 2mL cell culture
      • 8mL LB and 4mL cell culture
    • These three test tubes were then measured for their optical density. It was revealed that a dilution containing 10mL of LB medium and 2mL of our existing cell culture was optimal. Therefore 2 new culture tubes were filled with 10mL's of LB medium. To each we then added 2.5mL of one of the two cell cultures. We also added 12.5µg of Kanamycin antibiotics and an extra 5µL of IPTG to account for the dilution factor. The optical densities were then measured of these new culture tubes:
      • Protamine cell culture: 0.50
      • Poly(Arginine-Glycine) cell culture: 0.56
    • These Optical densities were adequate and therefore a t=0 sample was collected by pipetting 1.5mL of the cell culture into an eppendorf tube which was subsequently placed in the 4°C refrigerator.
  • The new cell cultures were then placed in the 37°C incubator and 1.5mL samples of each were taken every hour from then on for a further 5 hours. Each sample was immediately placed in the 4°C refrigerator.

Preparing an SDS-gel

Tomorrow we would like to run a number of samples on SDS gel to see whether the protein expression had been successful. In preparation of this we prepared two 12% SDS gels. To start with two solutions were prepared, a running and a stacking gel solution. The recipes for both are given below:

12% Running Gel (mL) Stacking Gel (mL)
Sterile Water 9.9 5.5
30% Acrylamide Mix 12 13
1.5M Tris-HCl Buffer (pH 8.8) 7.5 0
1M Tris-HCl Buffer (pH 6.8) 0 1
10% SDS 0.3 0.08
10% Ammonium Persulfate 0.3 0.08
TEMED 0.012 0.008

It should be remembered that the 10% Ammonium Persulfate and the TEMED should only be added once ready to pour, these will ensure the solutions harden into gels.

Having made the above solutions they were poured between too securely held glass plates. First the 12% running gel was poured and topped off with water to level it out. Once hard, the water could be poured off and the stacking gel could be added and allowed to hardened. Once hard the gels were wrapped in damp tissues and then aluminium foil. The entire package was then placed in the 4°C refrigerator overnight for use tomorrow.

15 August
2013

Running the SDS-Gel

On August 14th an SDS gel was prepared so that we would be able to run our expression samples today. Before being able to load the expression samples these first had to be prepared:

  • We had taken 6 1.5mL samples for each of the two expression cultures (Protamine-1-Optimized and Poly(Arginine-Glycine)). For each of the samples we wished to isolate the bacteria containing our proteins from the LB medium. This was done by centrifuging the samples at 13400 rpm in a tabletop centrifuge for 8 minutes.
  • During the centrifuging a pellet had formed in the bottom of the eppendorf tube. This contained the bacteria and therefore also our proteins. The supernatant could therefore be discarded.
  • To isolate our proteins from the bacteria we would have to add both BugBuster and Benzonse. For BugBuster 2mL was added for every 100mL of culture we wished to re-suspend. For Benzonase we would have to add 1/1000th of the volume of the BugBuster that we added. As this would be a very small amount for each of the samples separately a master mix was made by mixing 500µL of Bugbuster with 0.5µL of Benzonase.
  • Of this master mix 30*micro;L was added to each of the pellets. These were then placed in a tabletop shaker for 25-30 minutes at 25°C to resuspend the pellet.
  • Once resuspended the solution was spun down again for 5 minutes at 13400 rpm in a tabletop centrifuge. Once more a pellet of bacteria formed only this time the proteins could be found in the supernatant. A portion of this supernatant would therefore be loaded onto the SDS gel. However it was also possible that the proteins we wanted to see remained in the inclusion bodies in the bacteria, therefore we would also have to run these on gel.
  • 15µL of the supernatant was pipetted into a separate eppendorf tube ready for loading. The rest of the supernatant was then discarded.
  • !00µL of pH 8.8 buffer was then added to the pellet which resuspended. Of this solution 15µL was also pipetted into a separate eppendorf tube also ready for gel loading.
  • For each of the two cultures we now had 12 samples. six of these were supernatant samples containing primarily proteins, the other six were solutions containing dissolved bacterial pellets. Each sample tube contained 15µL of solution.
  • TO be able to see the samples on the gel a loading dye would have to be added to each sample. The loading dye was prepared by combining the following:
    • 500µL of Loading Dye
    • 1µL of DTT
  • This created a 2x loading buffer that could be added to all the samples.
  • 15µL of the loading dye solution was then added to each of the samples which were subsequently ready for loading.
  • 11µL of each sample was loaded into the separate columns of the 12% SDS gel which was subsequently run with the following program:
    • 15 minutes at 90V for the stacking equality.
    • 40 minutes at 150V through the running gel.
  • After running the gels they were shortly washed with water three times before being placed in a water bucket on the shaking table for 15 minutes.
  • Hereafter the water was removed and the gels were paced in Coomassie Blue staining medium for two hours.
  • The gels were then returned to water and left on the shaking table overnight.

Digestion Purification

On August 14th the new construct were digested along with the vecotrs pBR322 and pET28a. The constructs would have to be purified by performing a gel extraction whereas the vectors could be purified simply by performing the PCR purification protocol.

Purifying the Vectors

To purify the vectors after digestion, in preparation of the ligation the following steps were followed:

  • To the PCR product 5 volumes of PB buffer were added (In our case this was 250µL of PB buffer as we had 50µL of PRC product.)
  • This solution was placed in a QIAquick spin column and spun for 60 seconds at 13000 rpm. The flow through could be discarded.
  • Now 750µL of PE buffer could be added to the column before spinning it down once more for 60 seconds at 13000 rpm.
  • Having discarded the flow through the column was spun for a further 60 seconds again at 13000 rpm to remove the last of the PE buffer.
  • The column was then placed into a sealable eppendorf tube before adding 42µL of MilliQ water to the very centre membrane of the spin column and leaving it to stand for one minute.
  • The column was now placed in the centrifuge and spun for 60 seconds at 13000 rpm producing a solution containing the desired DNA.

Purifying the Inserts

The inserts too would need to be purified however as they were quite large this would not be possible using the PCR purification kit. This meant that we would have to load and extract the digestion products on an agarose gel. For each of the four constructs (EGFP, 1G70, Poly(Threonine-Lysine), Poly(Lysine-Serine)) we had four PCR products. Two of these had been digested for ligation into a pET28a vector and the other two solutions had been digested for ligation into pBR322.

  • The first step was the combination of the two solutions per construct which had been digested for ligation into the same vector.
  • After combination a total volume of 100µL had been attained. Therefore 20µL of 6x Loading Dye was added to each solution.
  • This entire solution was then loaded into a single column on a 1% agarose gel prepared by mixing the following:
    • 1.2g of Agarose
    • 120mL of TAE buffer
    • 12µL of CyberSafe
  • These gels were poured and let to harden before the samples were loaded into specially broadened columns.
  • Once fully loaded the gel was run at 100V for an hour.

After running the gel, gel extraction could be performed in the following manner:

  • First the gels were placed on a blue light to light up the bands and the correct bands were cut out. (These were the lower bands as the inserts had a smaller base length than the construct they were restricted out of).
  • A gel extraction column can hold a maximum of 400mg of gel. The gel cut-outs all weighed more than this and therefore each of the bands were split into two halves. Each half was placed in a separate 2mL eppendorf tube and weighed.
  • To each tube 3 volumes of QG buffer was added. A volume can be defined as the weight of the gel in mg transferred into µL. So a gel weighing 400mg would have a volume of 400µL, so 1200µL of QG would be added.
  • The eppendorf tubes containing the gel cut-outs and the QG buffer were placed in an incubator set at 50°C for 10 minutes, whilst vortexing the samples at regular (every 2 minutes) intervals until the gel had completely dissolved.
  • To these tubes 1 volume of isopropanol was added.
  • Each tube was then brought over into a QIAquick column and placed in the centrifuge where it was spun down for 60 seconds at 13000 rpm. The flow through was then discarded. If the volume of the gel, QG buffer and Isopropanol was larger than 800µL then this step was performed twice in the same column.
  • Now 750µL of PE buffer was added to the column before centrifuging at 13000 rpm for 60 seconds. After discarding the flow through the same amount was added and once more and again centrifuged.
  • Removing the flow through the column was then centrifuged again for 60 seconds at 13000 rpm removing the last of the PE buffer.
  • After bringing the column across into a sealable eppendorf tube 36µL of MilliQ water was pipetted onto the very centre membrane of the column which was then let to stand for 60 seconds. Subsequently the column was spun down at 13000 rpm for 60 seconds. The DNA is now in the flow through.
  • Remembering that we split the gel in half in the very first stage of this protocol, the two solutions containing the same DNA were combined so that a total volume of maximally 72µL of each insert was formed.

Nanodrop Results

For the ligation the concentrations of both the digested vectors and the digested inserts would have to be measured. The results can be seen in the tables below. The first table gives the concentration of both the vectors. The second gives the results for the digestion for ligation into pET28a and the third the results for ligation into pBR322

Vector Concentration (ng/µL)
pET28a 13.2
pBR322 5.2
pET28a Digested Inserts Concentration (ng/µL)
EGFP 17.6
1G70 8.8
Poly(Threonine-Lysine) 9.5
Poly(Lysine-Serine) 11.5
pBR322 Digested Insert Concentration (ng/µL)
EGFP 9.6
1G70 6.0
Poly(Threonine-Lysine) 3.9
Poly(Lysine-Serine) 3.2

As we can see the digestion was unsuccessful for the pBR322 vector. Its concentration is too low to be of use for the ligation which we performed next. Luckily however we had an older pBR322 digested sample in the freezer with a concentration of 13.1ng/µL which we could use.

Ligation

Having determined the concentrations of each of the constructs and the vectors we could start performing the calculations for the ligations. We wished to ligated 100ng of each of the vectors with each of the accordingly digested inserts. Ligation works best when there is more insert available than there is vector. Therefore we would first need to find out how many ng of insert will be needed for molar equality. This is done by dividing 100ng (the amount of vector we are using) by the number of bases in the vector. This amount would then be multiplied by the number of bases in the insert to reveal the mass in ng of insert we would need. Using this and with the concentrations of each insert at hand we could then determine the volume of DNA we would need to add to obtain a molar equality. Multiplying this volume by five would ensure a multitude of insert relative to the number of vectors in the ligation solutions.

Here the volume of each vector solution needed for 100ng of DNA:

Vector Concentration (ng/µL) 100g DNA (µL) Number of Bases in Vector
pBR322 13.1 7.6 4330
pET28a 13.2 7.6 5296

The following table gives the volumes needed for 5x molar equality of each of the inserts for the pET28a vector:

Construct Number of Bases Concentration (ng/µL) ng Needed for Molar Equality (ng) Volume Needed for Molar Equality (µL) Volume Needed for 5x Molar Equality (µL)
EGFP 732 9.6 13.8 1.44 7.1
1G70 417 6.0 12.7 2.12 10.6
Poly(Threonine-Lysine) 447 3.9 8.4 2.15 10.8
Poly(Lysine-Serine) 447 3.2 8.4 2.63 13.1


The following table gives the volumes needed for 5x molar equality of each of the inserts for the pBR322 vector:

Construct Number of Bases Concentration (ng/µL) ng Needed for Molar Equality (ng) Volume Needed for Molar Equality (µL) Volume Needed for 5x Molar Equality (µL)
EGFP 1056 9.6 13.8 1.44 7.1
1G70 741 8.8 17.1 1.94 9.7
Poly(Threonine-Lysine) 771 9.5 17.8 1.87 9.4
Poly(Lysine-Serine) 771 11.5 17.8 1.55 7.7

Using the above tables we now had all the information to be able to prepare our ligation solutions:

pET28a Ligation Solutions Vector Volume (µL) Insert Volume (µL) 10x Buffer (µL) Sterile Water (µL) Ligase (µL)
EGFP 7.6 7.1 2.5 6.8 1
1G70 7.6 10.6 2.5 3.3 1
Poly(Threonine-Lysine) 7.6 10.8 2.5 3.1 1
Poly(Lysine-Serine) 7.6 13.1 2.5 0.8 1
pBR322 Ligation Solutions Vector Volume (µL) Insert Volume (µL) 10x Buffer (µL) Sterile Water (µL) Ligase (µL)
EGFP 7.6 6.1 2.5 7.0 1
1G70 7.6 9.7 2.5 4.2 1
Poly(Threonine-Lysine) 7.6 9.4 2.5 4.5 1
Poly(Lysine-Serine) 7.6 7.7 2.5 7.2 1

Having prepared the above 25µL ligation solutions they were placed in the PCR apparatus with the following program:

  • Ligation: 2 hours at 25°C
  • Denaturation: 10 minutes at 65°C
  • Storage: FOREVER at 4°C

The ligation products were then left in the PCR apparatus at 4°C overnight ready for transformation and plating the following day.

16 August
2013

Transforming the Ligation Products

After having ligated our four newest constructs on August 15th into both pET28a and pBR322 we were now able to transform these into NB ready for growth on an agar plate.

  • First 1µL of the ligation product was pipetted into 20µL of NB bacteria. These were then left to stand on ice for 5 minutes.
  • The heat shock was performed by transferring the solutions to a 42°C water bath for 30 seconds before returning to ice for a further two minutes.
  • Then 80µL of SOC solution was added to the bacteria where after they were not returned to ice.
  • The transformation solutions were then incubated for 60 minutes at 37°C.

Plating

To grow cultures containing our ligation products we plated our transformation solutions. The constructs ligated into pET28a were plated on Kanamycin agar plates and those ligated into pBR322 were plated onto Ampicillin agar plates. This was done as follows:

  • All steps were performed in the vicinity of a blue bunsen flame.
  • Each transformation solution was pipetted in its entirety onto one of the plates.
  • Using a sterile spreader the solution was spread out over the plate.
  • The plates were then placed in a 37°C incubator overnight. As it was a Friday the incubator was set to 4°C for the remainder of the weekend after the plates had grown or 15 hours.


Week 5

19 August
2013

Colony Picking and PCR

Previously, on August 16th, agar plates had been prepared by transforming the ligations of the four newest constructs (EGFP, 1G70, Poly(Threonine-Lysine) and Poly(Lysine-Serine)) in both the pET28a and pBR322 vectors into NovaBlue bacteria and plating this entirety onto either Ampicillin or Kanamycin agar plates, according to the vector (Ampicillin plates for pBR322 ligated vectors and Kanamycin plates for pET28a ligated vectors.) Having grown these plates overnight, and storing them at 4°C for the remainder of the weekend we were now able to perform colony picking and PCR. For the colony picking a 5 pickings were taken from each of the eight agar plates and dissolved into 15µL of sterile water. The 'epjes' into which these were placed were carefully labelled as they would be referenced to later on. For the colony PCR two master mixes were prepared. One contained the primers for the pET28a vector PCR and one contained the primers needed for the pBR322 vector PCR. The master mixes were otherwise equal and consisted of the following:

  • 216µL of sterile water.
  • 300µL of Kapa 2G.
  • 30µL of the according FWD primer.
  • 30µL of the according RW primer.

Having prepared the two master mixes, 20 PCR eppendorf tubes per master mix were filled with 24µL of that master mix solution. To each of these prepared eppendorf tubes 1µL of the culture picking dilution was added, making care that the eppendorf tubes were labelled in the same manner as before and that the pBR322 ligated constructs were placed in the master mix containing the primers for that vector. The same was then done for the pET28a ligated constructs. Having prepared these samples they were placed in the PCR apparatus and set with the following protocol:

  • Initial Denaturation: 95°C for 3 minutes.
  • The following steps should be performed in this order, repeating the process a total of 34 times.
    • Denaturation: 95°C for 15 seconds.
    • Annealing: 58°C for 15 seconds.
    • Extension: 72°C for 20 seconds.
  • Final Extension: 72°C for 10 minutes.
  • Storage: 4°C FOREVER.

Having completed the PCR protocol 4µL of 6x loading dye was added to each of the samples. From this solution now 18µL was loaded onto a 1.5% agarose gel which was prepared by mixing the following:

  • 1.8g of Agarose
  • 120mL of TAE buffer
  • 12µL of Cybersafe

This gel was then run at 100V for 60 minutes.

Small cultures

Having run the gel with the colony PCR products we were able to analyse this and see in which of our colony pickings the ligated had been successful. For each of the ligated constructs, two successfully ligated pickings were then chosen for cell culture allowing us to multiply the DNA we had. This was done by adding 5µL of the original cell picking dissolved in water to an 8mL LB culture medium. To this culture medium we then also added 8µL of Ampicillin or Kanamycin dependant on the vector of the construct (Ampicillin for pBR322 ligated structures and Kanamycin for pET28a ligated structurs). These small culture tubes were then placed in a 37°C incubator for overnight growth.

Preparation for Protein Expression

Our previous test of protein expression had not been quite as successful as we had hoped as we had seen on August 16th. Therefore we were going to try again using two other constructs this time round namely: 1PJN and 1ETF both ligated into the pET28a vector. Each of these had already been transformed into BL21 bacteria and plated onto agar. We wished now to first grow these constructs on a small scale before transferring them to a larger culture for expression. To do this two culture tubes were prepared containing 10ml of LB and 10µL of Kanamycin. To each of these a pipet point was added with on the end a culture picking of one of the two constructs. These cultures were then placed in the 37°C incubator and left there for overnight growth. As we would be using the cell pellet formed after spinning down the expression product to measure the CEST contrast later this week, we would also need to provide a number of controls. One of these would be a cell pellet of a culture where no expression had taken place and a second would be the same only coated with poly-Lysines. To create the cell cultures for these controls 10mL of LB and 10µL of Kanamycin were mixed and to this solution a culture picking of 1ETF in BL21 bacteria was added. These too were cultured overnight at 37°C.

One further step was the preparation of two large cultures for the expression tomorrow. This was done by preparing 400mL of LB in two large erylmeyers. For the LB the following were mixed:

  • 4g of Peptones.
  • 4g of NaCl.
  • 2g of Yeast Extract.
  • 400mL of De-mineralised Water.

The solution was then autoclaved and left overnight ready for expression.


20 August
2013

Miniprepping new constructs

On August 18th the four newest constructs (EGFP, 1G70, Poly(Threonine-Lysine) and Poly(Lysine-Serine)) had been ligated into both pBR322 and pET28a vectors. On August 19th a number of samples of these ligation products were taken and cultured in 8mL culture tubes. Today we would isolate the DNA vectors from the culture medium, send off DNA for sequencing and ultimately transform the DNA to BL21 bacteria which could be plated. To start off DNA would have to be retained which meant miniprepping the cultures, the protocol for which is given here:

  • Firstly 700µL of each culture was pipetted into a storage tube along with 300µL of 50% Glycerol solution. The entire solution was then snap frozen in liquid nitrogen so that it could be stored in the -80°C freezer should we ever need to continue work with these vectors.