Team:TMU-Tokyo/Notebook

From 2013.igem.org

(Difference between revisions)
Line 130: Line 130:
<Hr>
<Hr>
-
  Reagents and Materials
+
  Reagents and Materials<br>
   NusleoSpin Gel and PCR Clean-up
   NusleoSpin Gel and PCR Clean-up
     <p>Contents :<br>
     <p>Contents :<br>

Revision as of 10:11, 25 September 2013



Plasmid Purification


Reagents and Materials
QIAprep Spin Miniprep Kit (QIAGEN)

Contents :
Buffer P1
Buffer P2
Buffer PB
Buffer EB

  • Collection tubes
  • Eppendorf Tubes
  • Vortex
  • Centrifugal machine
  • Collection tubes
  • Eppendorf Tubes
  • Vortex
  • Centrifugal machine

    1. Add 2 ml of culture medium of E.coli which cultured in overnights into an Eppendorf tube. Then, centrifuge the tube in room temperature (23~25℃), 130000 rpm for one minute.
    2. Add 250 μl Buffer P1 into the tube. Then, stir it with Vortex until deposition disappears.
    3. Add 250 μl Buffer P2 and mix the contents by inverting the tube (Don’t use the Vortex)
    4. Add 350 μl Buffer N3 and mix the contents by inverting the tube (Don’t use the Vortex.
    5. Centrifuge the tube in room temperature, 13000 rpm for 10 minutes.
    6. Move the supernatant by a pipette from the tube to the QIAprep Spin Column.
    7. Centrifuge in room temperature, 13000 rpm for 1 minute and throw away the flow through liquid which collected at the bottom of the column.
    8. Add 500 μl Buffer PB and centrifuge the tube in room temperature, 13000 rpm for 1 minute. Then, throw away the flow through liquid.
    9. Add 500 μl Buffer PE and centrifuge the tube in room temperature, 13000 rpm for 1 minute. Then, throw away the flow through liquid.
    10. Set the upper part of the QIAprep Spin Column into another Eppendorf tube.
    11. Add 50 μl EB buffer and left it at room temperature for 1 minute.
    12. Centrifuge in room temperature, 13000 rpm for 1 minute. The flow through liquid is the plasmid DNA solution.


    Restriction Enzyme Digestion


    Reagents and Materials
  • Eppendorf tube
  • milliQ
  • DNA solution
  • Digest Buffer
  • Restriction enzyme

  • Mix these solutions with the following quantities.

    Pattern1
    milliQ12 µl
    DNA solution5 µl
    Difest Buffer2 µl
    Restriction enzyme1 µl
    total20 µl
    Pattern 2
    milliQ12 µl
    DNA solution5 µl
    Difest Buffer2 µl
    Restriction enzyme ①1 µl
    Restriction enzyme ②1 µl
    total20 µl

    1. Incubate them at 37℃ for 1 hour.
    2. Incubate them at 60℃ for 15 minutes.


    Electrophoresis


    Reagents and Materials
  • Agarose gel
  • TAE Buffer
  • Loading Buffer
  • DNA solution
  • Eppendorf tube
  • Ethidium bromide

    1. Set gel in the electrophoresis tank anf pour the TAE Buffer into the tank.
    2. Put DNAsolution and Loading Buffer in the ratio of 1:2 into the Eppendorf tube and mix them.
    3. Load samples into wells.
    4. Do Electrophoresis at 100V for 40min.
    5. After electrophoresis, soak the gel into water including ethidium bromide for 20min.
    6. Observe the bands by ultraviolet radiation.


    DNA Purification (PCR / Digest)


    Reagents and Materials
    NusleoSpin Gel and PCR Clean-up

    Contents :
    Binding Buffer NT1
    Wash Buffer NT3
    Elution Buffer NE
    NucleoSpin Gel and PCR Clean-up Columns Collection Tubes

  • PCR / Digest solution
  • Centrifuge machine
  • Eppendorf tuber

    1. Put NT1 Buffer and gel into a tube and warm in at 50℃ for 5 minutes and dissolve it. (Add 200 μl NT1 Buffer for 100 mg of gel)
    2. Set the column into the Collection Tube and pour “Step1 solution” this column.
    3. Centrifuge it at 4℃ at 11,000rpm for 30seconds and throw away the flow through solution and set the column again.
    4. Add 700 µl Wash Buffer NT3 into the column and centrifuge it at 4℃ at 11,000 rpm for 30seconds.
    5. Through away the flow through solution and set the column again.
    6. Centrifuge at 4℃ at 11000 rpm for 1 minute.
    7. Set the column in to the micro tube and add 43 µl NE Buffer into the column.
    8. Left it for 1min at room temperature.
    9. Centrifuge at 4℃ at 11000rpm for 1 minute.

    PCR

    1. Switch on the thermal cycler.
    2. Make Cell suspension.
    3. Put the following solution into the PCR tube (Total: 50 μl)
    4. dNTP4 µl
      Primer(forward)5 µl
      Primer(reverse)5 µl
      Buffer10 µl

    5. Add 25 µl Cell suspension to the PCR tube.
    6. Add 1µl Taq polymerase and stir thecontents with Vortex mixer.